Panasonic AW-UE150WP Operating Instructions Manual

Also see for AW-UE150KE: Operating instructions Operating instructions Operating instructions Operating instructions

Contents

HDMIMake the settings for output from the HDMI connector.FormatSet the output format.The following format settings are possible depending on the [Format]setting in the [System] screen.Frequency System Format Format (HDMI)59.94Hz 2160/59.94p 2160/59.94p1080/59.94p2160/29.97p 2160/29.97p1080/29.97p1080/59.94p 1080/59.94p1080/59.94i 1080/59.94i1080/29.97p 1080/29.97p1080/29.97PsF 1080/29.97p1080/23.98p(59.94i) *1 1080/23.98p(59.94p) *2720/59.94p 720/59.94p50Hz 2160/50p 2160/50p1080/50p2160/25p 2160/25p1080/25p1080/50p 1080/50p1080/50i 1080/50i1080/25p 1080/25p1080/25PsF 1080/25p720/50p 720/50p24Hz 2160/24p 2160/24p1080/24p1080/24p 1080/24p23.98Hz 2160/23.98p 2160/23.98p1080/23.98p1080/23.98p 1080/23.98p1080/23.98PsF 1080/23.98p*1 It denotes “1080/23.98p over 59.94i”.*2 It denotes “1080/23.98p over 59.94p”.Factory settings: 2160/59.94p (AW-UE150WP/AW-UE150KP)2160/50p (AW-UE150WE/AW-UE150KE)HDR Output Select [SDR, HDR(2020), HDR(709)]Select the signal to be output when [Gamma Mode] is [HLG].SDR SDR outputHDR(2020) HDR output (BT.2020 equivalent color gamut)HDR(709) HDR output (BT.709 equivalent color gamut)Factory settings: HDR(2020)• [HDR Output Select] cannot be changed when [Gamma Mode] isother than [HLG] and [Video Sampling] is other than [4:2:2/10bit].(→ page 106)Video Sampling [4:2:2/10bit, 4:2:0/8bit]When [Format] in [HDMI] is [2160/59.94p] or [2160/50p], select thevideo sampling output from the HDMI connector.4:2:2/10bit Output in 4:2:2/10bit mode.4:2:0/8bit Output in 4:2:0/8bit mode.Factory settings: 4:2:2/10bit• When [Format] in [HDMI] is other than [2160/59.94p] or [2160/50p],[Video Sampling] cannot be changed and is fixed at [4:2:2/10bit].Bar [Camera, Colorbar]Switch between camera images and color bars.Camera Camera imagesColorbar Color barFactory settings: CameraColor Bar Type [Type1, Type2]Select the type of color bar to display.Type1: Type2:This is only enabled when [Bar] is set to [Colorbar].Factory settings: Type2• Even if the [HDR Output Select] for each of the outputs is either[HDR(2020)] or [HDR(709)], the color bar for SDR is output.Tone [Off, Low, Normal]Make the settings for the test tone signal (1 kHz) output while thecolor bar is displayed.Off Test tone is not output.Low Test tone is output at low volume.Normal Test tone is output at normal volume.This is only enabled when [Bar] is set to [Colorbar].Factory settings: NormalOSD MixSelect whether to turn off/on camera menu, status, and other displaysfor each output image.12G SDI/OPTICAL [Off*, On]3G SDI [Off*, On]MONI [Off, On*]HDMI [Off*, On]IP [Off, On*]Off The camera menus and statuses are not displayed on theoutput pictures covered by the setting items listed above.On The camera menus and statuses are displayed for the outputpictures covered by the setting items listed above.* : Factory settings• When this is set to [Off], the camera menu can be displayed forabout 1 minute after the unit is turned on.89Web screen configurations (continued)