Panasonic DIGA DMR-XS350EB Operating Instructions Manual

Also see for DIGA DMR-XS350EB: Service manual

Contents

106RQT9431Network SettingsThese settings are used when you will connect this unit to anetwork. The connection to the Internet may take time or theinternet may not be connected depending on the connectionenvironment. It is recommended that you use a broadbandconnection.Testing the connectionAlways test the connection when a LAN cable is connected or whennew “IP Address/DNS Settings” have been made.Press [FUNCTION MENU].Press [e, r] to select “Others”, then press [OK].Press [e, r] to select “Setup”, then press [OK].Press [e, r] to select “Network Settings”, thenpress [OK].Press [e, r] to select “IP Address/DNS Settings”,then press [OK].RETURNOKIP Address / DNS SettingsConnection TestOOnOOnOOnIP Address Auto-assignmentIP AddressSubnet MaskGateway AddressDNS-IP Auto-assignmentPrimary DNSSecondary DNSConnection Speed Auto-configureConnection Speed SettingMAC Address: 00-0b-97-e6-7a-aePress [e, r] to select “Connection Test”, thenpress [OK].“Testing” : The test is in progress.“OK” : The connection is completed.“Failed” : Please check the connection and settings.NotesPerform the “Connection Test” also when any change was made tothe “IP Address / DNS Settings”.If the connection test fails, it may be necessary to set the MACaddress of this unit at the router side. The MAC address can bedisplayed by selecting “Network Settings” and “IP Address / DNSSettings” in steps − (➔ above).Setting the IP addressIn most cases, default settings can normally be used without makingany changes.Set the IP address only when the router has no DHCP serverfunctions or when the router’s DHCP server function is disabled.After performing steps – (➔ above)Press [e, r] to select “IP Address Auto-assignment”, then press [w, q] to select “Off”.Press [e, r] to select “IP Address”, “SubnetMask” or “Gateway Address”, then press [OK].8 Enter numbers with the numbered buttons, thenpress [OK].y After checking the specifications for your broadband router,enter each number.If the number is unknown, then check the number of otherdevices such as personal computers connected via a LANcable. Assign a different number from those of otherdevices for “IP Address” and the same number for others.y If a wrong number is entered, then press [DEL].••192 . . .1IP AddressPlease input IP Address and press “OK”.The IP address will be cleared by pressing“OK” when there is no number input.Press “DEL” button if a wrong number isentered.0 - Number99 Press [w, q] to select “Yes”, then press [OK].NotesThe numeric input range is between 0 and 255.Setting the DNS-IPIn most cases, default settings can normally be used without makingany changes.When setting an assigned DNS server from your internet serviceprovider, perform the following settings.After performing steps – (➔ left)Press [e, r] to select “DNS-IP Auto-assignment”,then press [w, q] to select “Off”.Press [e, r] to select “Primary DNS” or“Secondary DNS”, then press [OK].8 Enter numbers with the numbered buttons, thenpress [OK].y Follow the instructions given by your internet serviceprovider and enter the numbers. If the number is unknown,then check the number of other devices such as personalcomputers connected via a LAN cable and assign the samenumber.y If a wrong number is entered, then press [DEL].9 Press [w, q] to select “Yes”, then press [OK].NotesThe numeric input range is between 0 and 255.Setting the connection speedWhen the connection test results in “Failed” after the IP and DNS-IPaddresses are assigned, perform the following settings.After performing steps – (➔ left)Press [e, r] to select “Connection Speed Auto-configure”, then press [w, q] to select “Off”.Press [e, r] to select “Connection Speed Setting”,then press [w, q] to select a connection speed.y Select a connection speed in accordance with theenvironment of the network connected.y When the settings are changed, the network connectionmay be disabled depending on the device.••