Panasonic DMR-E30 Operating Instructions Manual

Also see for DMR-E30: Operating instructions Installation instructions Operating instructions Bedienungsanleitung

Contents

important safety instructions

50RQT6559Advanced operationChanging the remote control code !?Most of the DVD recorders and players manufactured by Panasonicuse the same remote control system. If you have more than onepiece of equipment placed in proximity to each other, they may allrespond to the signal. If this occurs, you will have to alter the codeon the unit as well as on the remote control (the two must match)using the following procedure.≥Use “1”, the factory set code, under normal circumstances.1 Press [SETUP] to show the menus.2 Press [3, 4] to select “Set Up” andpress [1].3 Press [3, 4] to select “Remote Con-trol Code” and press [ENTER].4 Press [3, 4] to select the code (1, 2,or 3) and press [ENTER].The remote control code on the unit has been set.5 While pressing [ENTER] on theremote control, press the numberedbutton ([1], [2] or [3]) correspondingto the code you selected in step 4.The remote control code on the remote control has been set.6 Press [SETUP]If the unit doesn’t respond, you have entered the wrong code.Repeat step 5 to enter the correct code.[Note]≥The following display appears on the unit’s display if its code andthe remote control’s code are different. Change the remote con-trol’s code to suit the unit. The display disappears after about 5seconds.≥You can also set the main unit’s code without using the remotecontrol.1 Press [FUNCTIONS] on the main unit.2 Press [3, 4, 2, 1] to select “SETUP” and press [ENTER].3 Carry out procedure 2-4 above.4 Press [RETURN].DVD/TVDVDVCR Plus+ TV/VIDEO REC MODE RECCHVOLUMETVTVDVD1 2 37 8 90 1004 5 6SLOW/SEARCHSKIPDIRECT NAVIGATORTOPMENUMENURETURNFUNCTIONSPROG/CHECK DISPLAY TIME SLIPADD/DLTENTERPLAY LISTCANCELPOWERÍ ÍOPEN/CLOSESETUPERASE F Rec POSITION MEMORY MARKERAUDIO INPUT SELECT CM SKIPSTATUS FRAME2≥3≥4≥51≥652≥3≥4≥5FUNCTIONS RETURNTAB SELECTAntenna SystemAuto Channel SettingChannel CaptionPreset Channel CaptionManual Channel CaptionVCR Plusi CH SettingCATVChannelSET UPRETURNSet UpDiscVideoAudioDisplayTV ScreenThe unit’s remote control code51RQT6559Advanced operationChanging the unit’s settingsSee page 52 for menu and option details.1 Press [SETUP] to show the menus.2 Press [3, 4] to select the menu’s taband press [1].3 Press [3, 4] to select the menu andpress [ENTER].4 Press [3, 4] to select the option andpress [ENTER].The screen now shows the menu again.≥Some items require different operations. Read the following expla-nations.To return to the previous screenPress [RETURN].When you are finishedPress [SETUP].[DVD-V]The password screen is shown when you select levels 0 to 7.1. Input a 4-digit password with the numbered buttons.≥If you enter a wrong number, press [CANCEL] to erase it.2. Press [ENTER].≥The lock symbol appears closed to show the rating is locked.≥Do not forget your password.3. Press [ENTER] to confirm the 4 digits.[DVD-V]Change the settings when you have connected equipment throughthis unit’s DIGITAL AUDIO OUT terminal (➜page 47, [A]).Select the “Audio” tab and then “Digital Audio Output” by fol-lowing “Common procedures” (‹ left) to set up “PCM DownConversion”, “Dolby Digital” and “DTS”.Select how to output audio with a sampling frequency of 96 kHz.Select “On” if the equipment you connect cannot process signalswith a sampling frequency of 96 kHz.≥Select “Off” if you use analog connect irrespective of the type ofequipment.Off (Factory preset):Output as 96 kHz. There is no output if the disc has copy protection.Select “On” in this case.On:Converted to 48 kHz for output.Bitstream (Factory preset for Dolby Digital):Select if the equipment you connected can decode the signal.PCM:Select if the equipment you connected cannot decode Dolby Digitalsignal.Off (Factory preset for DTS):Select if the equipment you connected cannot decode DTS signal.IMPORTANTIf the equipment you connected cannot decode the signal, thesetting must be changed to PCM or Off. If not, signals theequipment cannot process will be output by this unit, causinghigh levels of noise which can damage your hearing and thespeakers.Common proceduresDVD/TVDVDVCR Plus+ TV/VIDEO REC MODE RECCHVOLUMETVTVDVD1 2 37 8 90 1004 5 6SLOW/SEARCHSKIPDIRECT NAVIGATORTOPMENUMENURETURNFUNCTIONSPROG/CHECK DISPLAY TIME SLIPADD/DLTENTERPLAY LISTCANCELPOWERÍ ÍOPEN/CLOSESETUPERASE F Rec POSITION MEMORY MARKERAUDIO INPUT SELECT CM SKIPSTATUS FRAME2≥3≥41RETURNCANCELNumberedbuttonsTAB SELECTAntenna SystemAuto Channel SettingChannel CaptionPreset Channel CaptionManual Channel CaptionVCR Plusi CH SettingCATVSET UPRETURNSet UpDiscVideoAudioDisplayTV ScreenOptionsMenusTabsChannelEntering a password (Ratings)Now, when you insert a DVD-Video that exceeds the ratings limityou set, a message appears on the television.Follow the on-screen instructions.Digital Audio OutputPCM Down ConversionDolby Digital and DTS!?