Panasonic DMR-E30 Operating Instructions Manual

Also see for DMR-E30: Operating instructions Installation instructions Operating instructions Bedienungsanleitung

Contents

important safety instructions

14RQT6559Getting startedSTEP 5 Selecting TV screen typeChange the settings if you:≥Connect the unit to a widescreen 16:9 aspect television.➜Set “TV Aspect” to “16:9”.≥Connect the unit through the COMPONENT video terminals(➜page 10) to a television compatible with progressive video sig-nals (480P).➜Set “TV Type” to “480P”.1 Press [SETUP] to show the menus.2 Press [3, 4] to select “TV Screen”and press [1].3 Press [3, 4] to select “TVAspect” and press [ENTER].4 Press [3, 4] to select “16:9” andpress [ENTER].3 Press [3, 4] to select “TVType” and press [ENTER].4 Press [3, 4] to select “480P” andpress [ENTER].≥When playing back, select Video in the on-screen menu and set“Transfer” according to the type of material being played(➜page 44).To return to the previous screenPress [RETURN].When you are finishedPress [SETUP].DVD/TVDVDVCR Plus+ TV/VIDEO REC MODE RECCHVOLUMETVTVDVD1 2 37 8 90 1004 5 6SLOW/SEARCHSKIPDIRECT NAVIGATORTOPMENUMENURETURNFUNCTIONSPROG/CHECK DISPLAY TIME SLIPADD/DLTENTERPLAY LISTCANCELPOWERÍ ÍOPEN/CLOSESETUPERASE F Rec POSITION MEMORY MARKERAUDIO INPUT SELECT CM SKIPSTATUS FRAME2≥3≥4RETURN1TAB SELECTAntenna SystemAuto Channel SettingChannel CaptionPreset Channel CaptionManual Channel CaptionVCR Plusi CH SettingCATVChannelSET UPRETURNSet UpDiscVideoAudioDisplayTV ScreenTABSELECTTV Aspect4:3 TV Settings for DVD-VideoTV mode(4:3)4:3LetterboxPan&ScanSET UPRETURNSet UpDiscVideoAudioDisplayTV Screen4:3 TV Settings for DVD-RAMTV Type 480IENTERChannelTV AspectTV Type!?SET UPSet UpDiscVideoAudioDisplaySELECTENTERTV AspectRETURN4:316:9TV ScreenChannel!?SET UPSet UpDiscVideoAudioDisplaySELECTENTERTV TypeRETURN480I480PTV ScreenChannel15RQT6559Getting startedSTEP 6 Television operation !?You can control televisions by entering the remote control code.1 Refer to the chart below for the codefor your television.2 Press and hold [Í, POWER TV] andenter the two-digit code with thenumbered buttons.≥For example: 01, press [0] ➜ [1].≥Test by turning on the television and changing channels.Repeat the procedure until you find the code that allowscorrect operation.[Note]≥If your television brand is not listed or if the code listed for yourtelevision does not allow control of your television, this remotecontrol is not compatible with your television.≥This remote control works with most recently manufactured televi-sions, but may not be able to control older models.∫ OperationPoint the remote control at the television.DVD/TVDVDVCR Plus+ TV/VIDEO REC MODE RECCHVOLUMETVTVDVD1 2 37 8 90 1004 5 6SLOW/SEARCHSKIPDIRECT NAVIGATORTOPMENUMENURETURNFUNCTIONSPROG/CHECK DISPLAY TIME SLIPADD/DLTENTERPLAY LISTCANCELPOWERÍ Í2TV/VIDEOW, X, CHDVD, TVr, s, VOLUME2Code No. Manufacturer01 Panasonic/National QUASAR02 Panasonic/National QUASAR03 MAGNAVOX SYLVANIA PHILIPS (RC-5)04 ZENITH05 THOMSON RCA GE06 SHARP07 SHARP08 SONY09 TOSHIBA10 SANYO FISHER11 JVC12 HITACHI13 MITSUBISHI14 SAMSUNG15 GOLDSTAR/LG16 GOLDSTAR/LG17 GOLDSTAR/LG18 SAMSUNG19 SAMSUNGOperation ButtonOn and off [Í, POWER TV]Video input mode [TV/VIDEO]Channels(Switch [DVD, TV] to “TV”.)[W, X, CH]orNumbered buttonsExample:Channel “5”: [0] ➜ [5]Volume [r, s, VOLUME]