Panasonic NV-MX500B Operating Instructions Manual

Also see for NV-MX500B: Operation instruction Service manual Operating instructions

Contents

VCR Mode-28-1 Set [VCR FUNCTIONS] >> [AV IN/OUT SETUP] >>[AV JACK] >> [IN/OUT].2 Continuing the aforesaid setup, select [A.DUB INPUT]>> [MIC] or [AV IN].≥Set to [AV IN] when external device is used, and to [MIC]when an external or built-in microphone is used.≥Switch the Movie Camera over to the Still PlaybackMode where you want to add new sound.3 Press the [A.DUB] Button (64) on the RemoteController.4 To start Audio Dubbing, press the [;] Button (78) onthe Remote Controller.To Cancel Audio DubbingPress the [;] Button (78) on the Remote Controller.The Movie Camera is in the Still Playback Mode again.To dub audio while listening to a pre-recorded soundWhen pausing the audio dubbing, [12bit AUDIO] on the[PLAYBACK FUNCTIONS] Sub-Menu is automatically set to[ST2] and you can check the pre-recorded sound. When amicrophone is used for audio dubbing, use headphones tolisten to the pre-recorded sound while dubbing the audio.(When using headphones, set [AV JACK] on the[AV IN/OUT SETUP] Sub-Menu to [OUT/PHONES].) Whenthe line input is used, you can dub audio while listening to apre-recorded sound from the speaker.To Play Back the Sound Recorded by 12bit AudioDubbingSet [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >>[12bit AUDIO] >> [ST2] or [MIX].ST1: It plays back only the original sound.ST2: It plays back only the sound added by Audio Dubbing.MIX: It plays back both the original sound and the soundadded by Audio Dubbing simultaneously.≥For other notes concerning this item, see -45-.Audio Level AdjustmentYou can adjust the Audio Level for audio dubbing byselecting a desired setting for [AUDIO LEVEL] on the[RECORDING SETUP] Sub-Menu of the[VCR FUNCTIONS] Main-Menu.When you set [MODE] of [AUDIO LEVEL] to any othersetting than [AUTO], the Audio Level Indication appears.Adjust the [GAIN] value.When this setting is changed, the [MIC LEVEL ADJ.] settingon the [ADVANCED FUNCTIONS] Sub-Menu of the(26)(51)M ENUPUSHSHUTTER/IRIS/VOL/JOGINDEX INDEXSELECTSTOPK L∫V/REWSTILL ADVTWsVOLr¥RECMULTI/P-IN-P A.DUBPLAYPAUSEFF/WSTILL ADV6 1 5;E D(64)(78)AUDIO LEVEL SETUPPRESS MENU TO RETURNMODE AUTO MNL MNL(AGC) (NO-AGC)(dB) -30 0 +6|||||||||-----GAIN[CAMERA FUNCTIONS] Main-Menu will likewise bechanged.For details, refer to Microphone Sensitivity Level Adjustment(-20-).To Reduce the Sound DistortionLower the output level of the external audio device. Or, setthe [MODE] of [AUDIO LEVEL] to [AUTO] or [MNL(AGC)].Copying on an S-VHS (or a VHS) Cassette(Dubbing)After connecting the Movie Camera and the VCR asillustrated, start the following procedures.1 AV Cable2 S-Video Cable (not supplied)≥If your TV is not equipped with AV Input Sockets, the 21-pinAdaptor (purchase separately) is necessary. Consult yourdealer.≥Be sure to press the [OSD] Button (-6-) on the RemoteController prior to copying so that no indications are visible.Otherwise, the displayed tape counter and functionindications are also copied.Movie Camera:1 Insert the recorded Cassette.VCR:2 Insert an unrecorded Cassette with an erasureprevention tab.≥If various setups (such as external input, tape speed,etc.) are required, please refer to the operatinginstructions of your VCR.Movie Camera:3 Press the [1] Button to start playback.VCR:4 Start recording.5 Press the Pause or Stop Button to stop recording.Movie Camera:6 Press the [∫] Button to stop playback.21-pin AdaptorMICAV IN/OUTPHONES/REMOTEUSB/EDITD(MINI)S-VIDEOIN/OUT12[VIDEO IN][AUDIO IN][S-VIDEO IN]