Panasonic NV-MX500B Operating Instructions Manual

Also see for NV-MX500B: Operation instruction Service manual Operating instructions

Contents

Others-41-ßA : Video Flash (setting to [AUTO]) -21-: Video Flash turned off (when lighted yellow,the Flash Sensor determined that the light isneeded) -21-, -44-£: Red Eye Reduction -21-ª To Change the Counter Display ModeBy changing [C.DISPLAY] on the [DISPLAY SETUP]Sub-Menu, you can change the Counter Display Mode toTape Counter Indication [COUNTER] (0:00.00), MemoryCounter Indication [MEMORY] (M0:00.00), and Time CodeIndication [TIMECODE] (0h00m00s00f). (-11-) By repeatedlypressing the [COUNTER] Button on the Remote Controller,you can change the Counter Display Mode.ª To Display Date/Time IndicationTo display Date/Time Indication, set the appropriateDate/Time in [DATE/TIME] on the [DISPLAY SETUP]Sub-Menu. (-11-)You can also press the [DATE/TIME] Button of the RemoteController repeatedly to display or change the Date/TimeIndication.ª To Change the Display ModeBy changing [DISPLAY] on the [DISPLAY SETUP]Sub-Menu, you can change the Display Mode to All FunctionDisplay [ALL], Partial Display [PARTIAL] and MinimumDisplay [OFF]. (-11-)Owner IDYou can register your name and address in your MovieCamera to identify the owner.1 Set [CAMERA FUNCTIONS] >> [OTHER FUNCTIONS]>> [OWNER ID SET] >> [YES].≥The [OWNER ID] Menu appears.2 Turn the [PUSH] Dial (26) to select [PIN NUMBER] andpress the [PUSH] Dial (26) to input desired numbers.3 Turn the [PUSH] Dial (26) to select numbers and pressthe [PUSH] Dial (26) to enter them.≥You can input 4 digits.4 Press the [∫] Button.5 Repeat Steps 2–4 to input desired characters for[NAME]/[HOUSE No.]/[POSTCODE].≥You can input up to 12 characters in [NAME], and up to11 characters in [HOUSE No.] and [POSTCODE].6 Press the [∫] Button to finish the setup.To verify Owner IDKeep pressing the [;] Button for approximately 5 seconds.To Check Owner IDIf Owner ID has already been set, carrying out Step 1 willdisplay [INPUT PIN NUMBER] on the screen. Input the PinNumber you have already selected. If the number is notcorrect, the screen will not change. If the number is correct,the contents of the setup will be displayed. (By repeatingSteps 2 to 4, you can change the contents.)Warning/Alarm IndicationsIf any one of the following indications lights up or flashes,please check the condition of the Movie Camera.3: Condensation has occurred. -48-Y: The accidental erasure prevention slider on theinserted Cassette is open (that is, set to [SAVE]).You are about to do audio dubbing on the unrecorded(blank) portion of the tape.No Cassette is inserted. -9-6: The Battery is low. Recharge it. -7-0: The built-in battery is low. -13-:: The video heads are dirty. -48-2END:The tape came to end during recording.REMOTE:Wrong Remote Controller Mode has been selected. -7-UNPLAYABLE TAPE(OTHER FORMAT):You are attempting to play back a tape section that hasbeen recorded with a different TV system.UNABLE TO A. DUB(LP RECORDED):Because the original recording was done in LP Mode,audio dubbing cannot be performed.UNABLE TO WRITE(WIDE MODE):You are attempting to record a Wide Mode picture on atape to a Card.INCOMPATIBLE TAPE:This Cassette is incompatible.PLEASE RE-OPERATEAFTER PUSHINGRESET BUTTON:Mechanism Irregular is detected. Press the [RESET]Button (-5-). This may solve the problem.TO SERVICE:It is a malfunction.CARD FULL:Card does not have sufficient memory remaining.Select Card Mode and delete unnecessary files.NO CARD:Card is not inserted.NO FILE:Card has no files recorded on it.UNPLAYABLE CARD:You are attempting to play back a data which is notcompatible with this Movie Camera.CARD ERROR:This Card is not compatible with this Movie Camera.COPY INHIBITED:Because the medium is protected by a copy guard,images cannot be recorded correctly.INCORRECTOPERATION:You are attempting to record to a tape in VCR Mode.You are pressing the [PHOTO SHOT] Button inMPEG4 Recording or Voice Recording.You are attempting to record to a tape in Card Mode.CONNECT USB CABLE:The [WEB CAMERA] Button is pressed with USBCable unconnected. Connect the USB Cable to theMovie Camera and the Personal Computer.DISCONNECT USB CABLE:You are pressing the Recording Start/Stop Button, the[PHOTO SHOT] Button or the [TITLE] Button in theWEB CAMERA Mode.You are pressing the [TITLE] Button in Camera Modeor VCR Mode with a USB Cable connected.You are attempting to record on a Card with a USBCable connected.CANCEL WEB CAMERA MODE:It is not possible to operate the [OFF/ON/MODE]Switch in the WEB CAMERA Mode.Notes and Hintsª Concerning the Power Supply≥When the Movie Camera is used for a long time, theCamera body becomes warm, but this is not a malfunction.≥If the [CHARGE] Lamp does not light up although theBattery is attached to the AC Adaptor, detach the Batteryand reattach it.≥Battery CGP-D110 and CGP-D105 cannot be charged withthis AC Adaptor.