Sanyo DSR-3000P Instruction Manual

Also see for DSR-3000P: Manual guide

Contents

Sanyo DSR-3000P Instruction Manual Manual pdf 73 page image

SPECIFICATIONSHard disk capacity : 80 GB (Installation of additional hard disk 80 GB (sold separately) possible)Television System : Based on PAL colour signal standardPicture Resolution : 720 x 288 (Field),720 x 576 (Frame)Compression : M-JPEGPicture Quality : 5 Levels (Basic, Normal, Enhanced, Fine, Super Fine)Recording Type : Frame or Field RecordingRecording Speed : 27 Levels.Recording Area : Normal Recording Area, Alarm Recording Area, Archive AreaPlayback : Playback, Still, SearchZoom : 2 Times Zoom FunctionSearch Mode•••• Time/Date Search : Search by time and date•••• Alarm Search : Search by alarm event list•••• Alarm Thumbnail Search : Search by alarm event thumbnails•••• Archive Area Search : Search Archive Area with event list•••• Smart Motion Search : Search by specifying a motion sensorMenu Language : English/French/German/SpanishVideo input terminal : 1.0 Vp-p/75 Ω, unbalanced, BNC x 1S- video input terminal : Separate YC signals, DIN connector (S terminal) x 1Y signal: 1.0 Vp-p/75 Ω, unbalanced, synchronous; C signal: 0.300 Vp-p/75 Ω, unbalancedDigital input terminal : RJ-45 x 1Digital SUB input terminal : RJ-45 x 1Audio input terminal : –8dBs, 27 kΩ unbalanced, RCA pin jack x 1Microphone input terminal : –60dBs 10kΩ unbalanced, 3.5mm mini jackVideo output terminal : 1.0 Vp-p/75 Ω, unbalanced, BNC x 1S- video output terminal : Separate YC signals, DIN connector (S terminal) x 1Y signal: 1.0 Vp-p/75 Ω, unbalanced, synchronous; C signal: 0.300 Vp-p/75 Ω, unbalancedLoop out terminal : 1.0 Vp-p/75 Ω, unbalanced, BNC x 1S- video loop out terminal : Separate YC signals, DIN connector (S terminal) x 1Y signal: 1.0 Vp-p/75 Ω, unbalanced, synchronous; C signal: 0.300 Vp-p/75 Ω, unbalancedDigital output terminal : RJ-45 x 1Digital SUB output terminal : RJ-45 x 1Audio output terminal : –8dBs, 600 Ω unbalanced, RCA pin jack x 1Compact Flash Slot : Compact Flash Type 2 (Front)PC Card Slot : PCMCIA Type 2 (Rear) for SCSI or Ethernet cardRS-232C terminal : D- SUB 9pin (for PC)Control connectors•••• RS-485 terminal : Push lock (3 terminals: A, B, C (GND))•••• Remote Control terminal : 1 input for resister alley switch•••• Alarm in terminal : 1 input (Normal Open Low level active)•••• Alarm out terminal : 1 output (Normal 5V Low level active)•••• Alarm reset terminal : 1 input (Normal Open Low level active)•••• SW out terminal : 1 output (Normal 5V Low level active)•••• NON Rec out terminal : 1 output (Normal 5V Low level active)•••• Clock Adjust in terminal : 1 input (Normal Open Low level active)•••• Clock Adjust out terminal : 1 output (Normal 5V Low level active)•••• Warning out terminal : 1 output (Normal 5V Low level active)•••• Disk Full out terminal : 1 output (Normal 5V Low level active)•••• Alarm Full out terminal : 1 output (Normal 5V Low level active)Power : AC 220 – 240 V, 50 HzPower consumption : 27 W 260 mAOperating environment : Temperature: 5°C to 40°C, Humidity: 10 to 80%Dimensions : 420 (W) x 86 (H) x 364.5 (D) mmWeight : Approx. 5.5 kgProducts are subject to change in design and specifications without notice and without incurring any obligation.72 English

/ 74

Related manuals for Sanyo DSR-3000P