Sanyo DSR-M814 Instruction Manual

Also see for DSR-M814: Service manual addendum Service manual

Contents

1PRECAUTIONCAUTION: Changes or modifications not expresslyapproved by the manufacturer may void the user’s authorityto operate this equipment.This equipment has been tested and found to comply withthe limits for a Class B digital device, pursuant to part 15 ofthe FCC Rules.These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation.This equipment generated, uses and can radiate radiofrequency energy and, if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. However, there is noguarantee that interference will not occur in a particularinstallation.If this equipment does cause harmful interference radio ortelevision reception, which can be determined by turningthe equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the followingmeasures:z Reorient or relocate the receiving antenna.z Increase the separation between the equipment andreceiver.z Connect the equipment into an outlet on a circuitdifferent from that to which the receiver is connected.z Consult the dealer or an experienced radio/TVtechnician for help.For the customers in CanadaLocationFor safe operation and satisfactory performance of yourunit, keep the following in mind when selecting a place forits installation:z Shield it from direct sunlight and keep it away fromsources of intense heat.z Avoid dusty or humid places.z Avoid places with insufficient ventilation for proper heatdissipation. Do not block the ventilation holes at the topand bottom of the unit. Do not place the unit on a carpetbecause this will block the ventilation holes.z Install the unit in a horizontal position only.z Avoid locations subject to strong vibrations.z Avoid moving the unit between cold and hot locations.z Do not place the unit directly on top of a monitor TV, asthis may cause playback or recording problems.Avoiding Electrical Shock and Firez Do not handle the power cord with wet hands.z Do not pull on the power cord when disconnecting itfrom an AC wall outlet. Grasp it by the plug.z If any liquid is spilled on the unit, unplug the power cordimmediately and have the unit inspected at a factory-authorised service center.z Do not place anything directly on top of this unit.SERVICEThis unit is a precision instruments and if treated with care,will provide years of satisfactory performance.However, in the event of a problem, the owner is advisednot to attempt to make repairs or open the cabinet.Servicing should always be referred to your dealer orSanyo Authorized Service Centre.CAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOTREMOVE COVER (OR BACK).NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.WARNING: To reduce the risk of fire or electric shock, donot expose this appliance to rain or moisture.The lightning flash with arrowhead symbol, within anequilateral triangle, is intended to alert the user to thepresence of uninsulated “dangerous voltage” within theproduct’s enclosure that may be of sufficient magnitude toconstitute a risk of electric shock to persons.The exclamation point within an equilateral triangle isintended to alert the user to the presence of importantoperating and maintenance (servicing) instructions in theliterature accompanying the product.This class B digital apparatus complies with CanadianICES-003.CAUTIONDanger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent typerecommended by the manufacturer.Discard used batteries according to the manufacture’sinstructions.Declaration of ConformityModel Number : DSR-M814Trade Name : SANYOResponsible party : SANYO FISHER COMPANYAddress : 21605 Plummer Street,Chatsworth, California 91311Telephone No. : (818) 998-7322z This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) this device may not cause harmfulinterference,and(2) this device must accept any interference received,including interference that may cause undesiredoperation.e00_VDH_M814.book Page 1 Thursday, October 28, 2004 9:59 AM