12 Important Notes WAGO-I/O-SYSTEM 750750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iParManualVersion 1.4.0, valid from HW/SW Version 01/01Pos: 17 /Alle Serien (Allgemeine Module)/Überschriften für alle Serien/Wichtige Erläuterungen/Wichtige Erläuterungen - Überschrift 1 @ 4\mod_1241428899156_21.docx @ 32170 @ 1 @ 12 Important NotesPos: 18.1 /Alle Serien (Allgemeine Dokumente) (Allgemeine Module)/Wichtige Erläuterungen/Wichtige Erläuterungen - Einleitung @ 3\mod_1221059818031_21.docx @ 21717 @ @ 1This section includes an overall summary of the most important safetyrequirements and notes that are mentioned in each individual section. To protectyour health and prevent damage to devices as well, it is imperative to read andcarefully follow the safety guidelines.Pos: 18.2 /Alle Serien (Allgemeine Module)/Überschriften für alle Serien/Wichtige ErläuterungenRechtliche Grundlagen - Überschrift 2 @ 3\mod_1221060626343_21.docx @ 21726 @ 2 @ 12.1 Legal BasesPos: 18.3 /Alle Serien (Allgemeine Dokumente) (Allgemeine Module)/Wichtige Erläuterungen/Änderungsvorbehalt - Überschrift 3 und Inhalt @ 3\mod_1221060036484_21.docx @ 21720 @ 3 @ 12.1.1 Subject to ChangesWAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for anyalterations or modifications that serve to increase the efficiency of technicalprogress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising fromthe granting of patents or from the legal protection of utility patents. Third-partyproducts are always mentioned without any reference to patent rights. Thus, theexistence of such rights cannot be excluded.Pos: 18.4 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/PersonalqualifikationPersonalqualifikation 750-xxxx - Überschrift 3 und Inhalt @ 3\mod_1224061208046_21.docx @ 24063 @ 3 @ 12.1.2 Personnel QualificationsAll sequences implemented on WAGO-I/O-SYSTEM 750 devices may only becarried out by electrical specialists with sufficient knowledge in automation. Thespecialists must be familiar with the current norms and guidelines for the devicesand automated environments.All changes to the coupler or controller should always be carried out by qualifiedpersonnel with sufficient skills in PLC programming.Pos: 18.5 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- und sonstige Hinweise/Gefahr/Gefahr: Austausch von PROFIsafe-Busklemmen nur durch sicherheitstechnisch sachkundige Personen @ 4\mod_1239786227890_21.docx @ 30470 @ @ 1Only personnel trained in safety-related procedures may perform the work!Adding, exchanging and starting up PROFIsafe I/O modules may only be carriedout by personnel trained in safety-related procedures!Pos: 18.6 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Bestimmungsgemäße VerwendungBestimmungsgemäße Verwendung 750-xxxx - Überschrift 3 und Inhalt @ 3\mod_1224064151234_21.docx @ 24070 @ 3 @ 12.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance withUnderlying ProvisionsFieldbus couplers, fieldbus controllers and I/O modules found in the modularWAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors andtransmit them to actuators or higher-level control systems. Using programmablecontrollers, the signals can also be (pre-) processed.The devices have been developed for use in an environment that meets the IP20protection class criteria. Protection against finger injury and solid impurities up to12.5 mm diameter is assured; protection against water damage is not ensured.Unless otherwise specified, operation of the devices in wet and dustyenvironments is prohibited.
