H3C S5560-EI series manuals
S5560-EI series
Table of contents
- installation guide
- obtaining documentation
- documentation feedback
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Preparing for installation
- Temperature/humidity
- Laser safety
- Installing the switch
- Installing the switch in a 19-inch rack
- Installation accessories
- Rack-mounting by using front mounting brackets
- Rack-mounting by using front mounting brackets and mounting rail assemblies (S5560-54QS-EI)
- Mounting the switch on a workbench
- Grounding the switch with a grounding conductor buried in the earth ground
- Grounding the switch by using the AC power cord
- Installing/removing a fan tray
- Removing a fan tray
- Installing/removing a power module
- Installing a PSR150 power module
- Removing a PSR150 power module
- Removing a PSR360-56A/PSR720-56A/PSR1110-56A power module
- Connecting the power cord
- Connecting an AC power cord to the switch
- Connecting a DC power cord to the switch
- Connecting the PSR150-D1
- Connecting the PSR360-56A/PSR720-56A/PSR1110-56A
- Installing/removing an expansion card
- Removing an expansion card
- Accessing the switch for the first time
- Connecting the Mini USB console cable
- Setting terminal parameters
- Setting up an IRF fabric
- Planning IRF fabric setup
- Planning IRF topology and connections
- Identifying physical IRF ports on the member switches
- Configuring basic IRF settings
- Verifying the IRF fabric setup
- Maintenance and troubleshooting
- Hot swappable power module failure
- Fan failure
- Configuration terminal display problems
- Appendix A Chassis views and technical specifications
- S5560-54S-EI
- S5560-30F-EI
- S5560-30C-EI
- S5560-30C-PWR-EI
- S5560-34C-EI
- S5560-54C-EI
- S5560-54C-PWR-EI
- S5560-54QS-EI
- Appendix B FRUs and compatibility matrixes
- Hot-swappable power modules
- Hot-swappable fan trays
- Interface card operating mode
- Connecting cables to the copper ports on the interface cards
- Appendix C Ports and LEDs
- USB port
- SFP port
- QSFP+ port
- Combo interface
- RPS status LED
- BASE-T autosensing Ethernet port LED
- SFP+ port LED
- Management Ethernet port LEDs
- Port status LED on the expansion card
- Appendix D Cooling system
S5560-EI series
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Introduction
- Collecting common log messages
- Collecting diagnostic log messages
- Contacting technical support
- Troubleshooting hardware
- Troubleshooting flowchart
- Operating power module failure
- Newly installed power module failure
- Fan tray failure
- Related commands
- Troubleshooting ACL
- ACL application failure without an error message
- Packet loss or forwarding failure
- Troubleshooting IRF
- Troubleshooting Ethernet link aggregation
- Troubleshooting ports
- Copper port remains in down state
- Non-H3C transceiver module
- Transceiver module does not support digital diagnosis
- Error frames (for example, CRC errors) on a port
- Failure to receive packets
- Solution
- Failure to send packets
- Troubleshooting system management
- High memory utilization
- Troubleshooting other problems
- Layer 3 forwarding failure
Related products
S5500-EI seriesS5560-HI SeriesS5150-EI SeriesS5120-EI SeriesS5510 SeriesS5500-SI Seriess5800 seriesH3C S5600 Seriess5820x seriesS5120-SI SeriesH3C categories
Switch
Network Router
Network Hardware
IP Access Controllers
Firewall
Control Unit
Wireless Access Point
Server
Gateway
Wireless Router
manualsdatabase
Your AI-powered manual search engine