GE C60 Instruction Manual

Also see for C60: Communications manual Communications guide Instruction manual Instruction manual Instruction manual

Contents

B-46 C60 Breaker Management Relay GE MultilinB.3 MEMORY MAPPING APPENDIX BBF201TEXT8 8 CHARACTER ASCII PASSCODE4 registers, 16 Bits: 1st Char MSB, 2nd Char. LSBF202TEXT20 20 CHARACTER ASCII TEXT10 registers, 16 Bits: 1st Char MSB, 2nd Char. LSBF203TEXT16 16 CHARACTER ASCII TEXTF204TEXT80 80 CHARACTER ASCII TEXTF205TEXT12 12 CHARACTER ASCII TEXTF206TEXT6 6 CHARACTER ASCII TEXTF207TEXT4 4 CHARACTER ASCII TEXTF208TEXT2 2 CHARACTER ASCII TEXTF222ENUMERATION TEST ENUMERATION0 = Test Enumeration 0, 1 = Test Enumeration 1F300UR_UINT16 FLEXLOGIC BASE TYPE (6 bit type)The FlexLogicô BASE type is 6 bits and is combined with a 9 bitdescriptor and 1 bit for protection element to form a 16 bit value.The combined bits are of the form: PTTTTTTDDDDDDDDD,where P bit if set, indicates that the FlexLogicô type is associatedwith a protection element state and T represents bits for the BASEtype, and D represents bits for the descriptor.The values in square brackets indicate the base type with P prefix[PTTTTTT] and the values in round brackets indicate the descrip-tor range.[0] Off(0) this is boolean FALSE value[0] On (1)This is boolean TRUE value[2] CONTACT INPUTS (1 - 96)[3] CONTACT INPUTS OFF (1-96)[4] VIRTUAL INPUTS (1-64)[6] VIRTUAL OUTPUTS (1-64)[10] CONTACT OUTPUTS VOLTAGE DETECTED (1-64)[11] CONTACT OUTPUTS VOLTAGE OFF DETECTED (1-64)[12] CONTACT OUTPUTS CURRENT DETECTED (1-64)[13] CONTACT OUTPUTS CURRENT OFF DETECTED (1-64)[14] REMOTE INPUTS (1-32)[28] INSERT (Via Keypad only)[32] END[34] NOT (1 INPUT)[36] 2 INPUT XOR (0)[38] LATCH SET/RESET (2 INPUTS)[40] OR (2-16 INPUTS)[42] AND (2-16 INPUTS)[44] NOR (2-16 INPUTS)[46] NAND (2-16 INPUTS)[48] TIMER (1-32)[50] ASSIGN VIRTUAL OUTPUT (1 - 64)[52] SELF-TEST ERROR (See F141 for range)[56] ACTIVE SETTING GROUP (1-8)[62] MISCELLANEOUS EVENTS (See F146 for range)[64-127] ELEMENT STATES(Refer to Memory Map Element States Section)F400UR_UINT16 CT/VT BANK SELECTIONF500UR_UINT16 PACKED BITFIELDFirst register indicates I/O state with bits 0(MSB)-15(LSB) corre-sponding to I/0 state 1-16. The second register indicates I/O statewith bits 0-15 corresponding to I/0 state 17-32 (if required) Thethird register indicates I/O state with bits 0-15 corresponding to I/0state 33-48 (if required). The fourth register indicates I/O state withbits 0-15 corresponding to I/0 state 49-64 (if required).The number of registers required is determined by the specificdata item. A bit value of 0 = Off, 1 = OnF501UR_UINT16 LED STATUSLow byte of register indicates LED status with bit 0 representingthe top LED and bit 7 the bottom LED. A bit value of 1 indicatesthe LED is on, 0 indicates the LED is off.F502BITFIELD ELEMENT OPERATE STATESEach bit contains the operate state for an element. See the F124format code for a list of element IDs. The operate bit for element IDX is bit [X mod 16] in register [X/16].bitmask bank selection0 Card 1 Contact 1 to 41 Card 1 Contact 5 to 82 Card 2 Contact 1 to 43 Card 2 Contact 5 to 84 Card 3 Contact 1 to 45 Card 3 Contact 5 to 8www . ElectricalPartManuals . com