Contents - Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Specifications
- Hydraulic Oil Specifications
- Hydraulic Component Specifications
- Hydraulic Hose and Fitting Torque Specifications
- Torque Procedure
- Repair Procedures
- Platform Controls
- Circuit Board
- Joystick
- Platfrom Controls Alarm
- Platform Components
- Platform Extension Deck
- Scissor Components
- Scissor Assembly, GS-2669 DC
- Scissor Assembly, GS-3369 DC
- Scissor Assembly, GS-4069 DC
- Wear Pads
- Lift Cylinders
- November
- Ground Controls
- Software Revision Level
- Machine Setup
- Auxiliary Platform Lowering
- Level Sensor - Models with Outriggers
- Service Override Mode
- Hydraulic Pump
- How to Calibrate the Hydraulic Pump
- Manifolds
- a Function Manifold Components
- Valve Adjustments - Function Manifold
- How to Adjust the Oscillate Relief Valve
- How to Adjust the Steer Relief Valve
- How to Adjust the Platform Up Relief Valve - Models without Platform Overload
- Outrigger Manifold Components
- Valve Coils
- Hydraulic Tank
- Steer Cylinder
- Oscillate Cylinder
- Steer Angle Sensor
- Non-steer Axle Components
- Drive Hub
- Outrigger Components
- Outrigger Calibration
- Platform Overload Components
- Platform Overload Recovery
- Fault Codes
- GCON I/O Map
- Operation Indicator Codes (OIC)
- Troubleshooting "HXXX" and "PXXX" Faults
- Fault Inspection Procedure
- Type "HXXX" Faults
- Type "PXXX" Faults
- Type "UXXX" Faults
- Type "FXXX" Faults
- Type "CXXX" Faults
- Section 5 Schematics
- Electrical Schematic Abbreviations and Wire Color Legends
- Hydraulic Component Legend
- Electrical Symbols Legend
- Hydraulic Symbols Legend
- Limit Switch Legend
- Fuse, Ground and Platform Control Boxes
- Fuse Box Layout, All Models
- Ground Control Box Layout, All Models
- Platform Control Box Layout, Models with 2 Speed Lift
- Control Box Layout, Models with Proportional Lift
- Electrical Schematics - ANSI / CSA
- Electrical Schematic, GS-2669 DC and GS-3369 DC with 2 Speed Lift, (ANSI CSA) (to serial number GS6915-6388)
- Electrical Schematic, GS-2669 DC and GS-3369 DC with Proportional Lift, (ANSI CSA) (from serial number GS6915-6389 to GS6915-7719)
- Electrical Schematic, GS-2669 DC and GS-3369 DC with Proportional Lift, (ANSI CSA) (from serial number GS6915-7720)
- Electrical Schematic, GS-4069 DC with 2 Speed Lift, (ANSI / CSA) (to serial number GS6915-6388)
- Electrical Schematic, GS-4069 DC with Proportional Lift, (ANSI / CSA) (from serial number GS6915-7720)
- Electrical Schematics - AS / CE
- Electrical Schematic, GS-2669 DC and GS-3369 DC with 2 Speed Lift, (AS / CE to serial number GS6915-6388)
- Electrical Schematic, GS-2669 DC and GS-3369 DC with Proportional Lift, (AS CE) (from serial number GS6915-6389 to GS6915-7719)
- Electrical Schematic, GS-2669 DC and GS-3369 DC with Proportional Lift, (AS CE) (from serial number GS6915-7720)
- Electrical Schematic, GS-4069 DC with 2 Speed Lift, (AS / CE) (to serial number GS6915-6388)
- Electrical Schematic, GS-4069 DC with Proportional Lift, (AS / CE) (from serial number GS6915-6389 to GS6915-7719)
- Electrical Schematic, GS-4069 DC with Proportional Lift, (AS / CE) (from serial number GS6915-7720)
- Hydraulic Schematics
- Hydraulic Schematic, GS-2669 DC and GS-3369 DC with 2 Speed Lift (to serial number GS6915-6388)
- Hydraulic Schematic, GS-2669 DC and GS-3369 DC with Proportional Lift (from serial number GS6915-6389)
- Hydraulic Schematic, GS-4069 DC with 2 Speed Lift (to serial number GS6915-6388)
- Hydraulic Schematic, GS-4069 DC with Proportional Lift (from serial number GS6915-6389)
|
Service and Repair Manual November 2016Ground Controls38 GS-2669 DC • GS-3369 DC • GS-4069 DC Part No. 1272220GT4-5 Level Sensor - M odels with Outriggers4-5Level Sensor - Models withOutriggersThe Electronic Control Module (ECM) isprogrammed to deactivate the lift and drivefunctions and activate an alarm when a signal isreceived from the level sensor.When the outriggers are stowed, the tilt alarmsounds when the incline of the chassis exceeds 2°to the side.When the outriggers are deployed, functions will bedisabled and and fault will be displayed when theincline of the chassis exceeds 0.8° to the side.At all times, the tilt alarm sounds when the inclineof the chassis exceeds 3° to the front or rear.How to Install the Outrigger LevelSensorTip-over hazard. Failure to installor calibrate the level sensor asinstructed will compromisemachine stability and cause themachine to tip over, resulting indeath or serious injury. Do notinstall or calibrate the levelsensor other than specified inthis procedure.Note: Perform this procedure with the machine ona firm, level surface that is free of obstructions.1 Turn the key switch to the off position andpush in the red Emergency Stop button to theoff position at both the ground and platformcontrols.2 Locate the level sensor in the ground controlscompartment.3 Tag and disconnect the wire harness from thelevel sensor.1 ground control box2 level sensor4 Remove the level sensor retaining fastenersand remove the level sensor from themachine.
|
