Contents - September
- safety rules
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Specifications
- Performance Specifications
- Hydraulic Component Specifications
- Manifold Component Specifications
- Machine Torque Specifications
- Hydraulic Hose and Fitting Torque Specifications
- Torque Procedure
- Section 3 Repair Procedures
- repair procedures
- Platform Controls
- Joysticks
- How to Adjust the Joystick Max-out Setting
- How to Adjust the Joystick Ramp Rate Setting
- How to Adjust the Joystick Threshold Setting
- How to Calibrate the Boom Angle Sensor
- Platform Components
- Platform Leveling Slave Cylinder
- Platform Rotator
- How to Bleed the Platform Rotator
- Platform Overload System
- Jib Boom Components
- Jib Boom Lift Cylinder
- Boom Components
- How to Repair the Cable Track
- How to Remove the Boom
- Boom Lift Cylinder
- Boom Extension Cylinder
- Boom Extend/Retract Cables
- How to Replace the Boom Extend/Retract Cables
- Platform Leveling Master Cylinder
- Engines
- How to Install the Flex Plate
- How to install the Pump and Bell Housing Assembly
- Ground Controls
- Hydraulic Pumps
- Drive Pump
- How to Prime the Pump
- Valve Adjustments - Function Manifold
- How to Adjust the Boom Extend Relief Valve
- Brake/Two-Speed Manifold Components
- Turntable Rotation Manifold Components
- Platform Rotate Manifold Components
- Platform Manifold Components, S-80
- Platform Manifold Components, S-85
- WD Traction Manifold Components
- Drive Oil Diverter Manifold Components (welder option)
- Valve Adjustments - Traction Manifold
- Valve Coils
- How to Test a Coil Diode
- Fuel and Hydraulic Tanks
- Hydraulic Tank
- Turntable Rotation Components
- How to Remove the Turntable Rotation Hydraulic Motor
- How to Adjust the Turntable Rotation Gear Backlash
- Steer Axle Components
- Drive Motors
- Steer Cylinders
- Non-steer Axle Components
- Oscillating Axle Components
- Oscillate Directional Valve
- How to Set Up the Directional Valve Linkage
- Section 4 Fault Codes
- Control System Fault Codes
- Fault Code Display - Deutz and Perkins Models
- Fault Code Display - Flashing and Solid LED's Deutz D 2.9 L4 and Perkins 404F-22 Models
- Soft Key Functions and Icons Deutz D 2.9 L4 and Perkins 404F-22 Models
- Main Menu Structure - Deutz D 2.9 L4 Models
- Main Menu Structure - Perkins 404F-22 Models
- Deutz D 2.9 L4 Engine Fault Codes
- Perkins 404F-22 Engine Fault Codes
- Continental TME27 Engine Fault Codes
- Section 5 Schematics
- Electrical Symbol Legend
- Hydraulic Symbols Legend
- Relay and Fuse Panel Legend - Deutz TD2011L04i
- Relay and Fuse Panel Legend - Perkins 804D-33
- Connector Pin Legends
- Continental TME27 Engine Harness
- S-80X Ground Control Box Wiring Diagram
- Deutz TD2.9 L4 Engine Harness
- Perkins 404F-22T Engine Harness
- Electrical Schematics, S-80X – ANSI and CSA Models
- Electrical Schematic, S-80X - Deutz TD2.9 L4 Models (ANSI / CSA)
- Ground Control Box, S-80X - Deutz TD2.9 L4 Models (ANSI / CSA)
- Platform Control Box, S-80X - Deutz TD2.9 L4 Models (ANSI / CSA)
- Electrical Schematic, S-80X - Deutz TD2011L04i Models (ANSI / CSA)
- Ground Control Box, S-80X - Deutz TD2011L04i Models (ANSI / CSA)
- Platform Control Box, S-80X - Deutz TD2011L04i Models (ANSI / CSA)
- Electrical Schematic, S-80X - Perkins 404F-22T Models (ANSI / CSA)
- Ground Control Box, S-80X - Perkins 404F-22T Models (ANSI / CSA)
- Platform Control Box, S-80X - Perkins 404F-22T Models (ANSI / CSA)
- Electrical Schematic, S-80X - Perkins 804D-33 Models (ANSI / CSA)
- Ground Control Box, S-80X - Perkins 804D-33 Models (ANSI / CSA)
- Platform Control Box, S-80X - Perkins 804D-33 Models (ANSI / CSA)
- Electrical Schematic, S-80X - Continental TME27 Models (ANSI / CSA)
- Ground Control Box, S-80X - Continental TME27 Models (ANSI / CSA)
- Platform Control Box, S-80X - Continental TME27 Models (ANSI / CSA)
- Electrical Schematics, S-80, S-85 – ANSI and CSA Models
- Deutz TD2.9 L4 Models (ANSI / CSA)
- Ground Control Box, S-80 • S
- Platform Control Box, S-80 • S
- Electrical Schematic, S-80 • S
- Deutz TD2011L04i Models (ANSI / CSA)
- Perkins 404F-22T Models (ANSI / CSA)
- Perkins 804D-33 Models (ANSI / CSA)
- Continental TME27 Models (ANSI / CSA)
- Electrical Schematics, S-80, S-85 – CE Models
- Electrical Schematic, S-80 • S-85 - Deutz TD2.9 L4 Models (CE)
- Ground Control Box, S-80 • S-85 - Deutz TD2.9 L4 Models (CE)
- Platform Control Box, S-80 • S-85 - Deutz TD2.9 L4 Models (CE)
- Electrical Schematic, S-80 • S-85 - Deutz TD2011L04i Models (CE)
- Ground Control Box, S-80 • S-85 - Deutz TD2011L04i Models (CE)
- Platform Control Box, S-80 • S-85 - Deutz TD2011L04i Models (CE)
- Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (CE)
- Ground Control Box, S-80 • S-85 - Perkins 804D-33 Models (CE)
- Platform Control Box, S-80 • S-85 - Perkins 804D-33 Models (CE)
- Electrical Schematic, S-80 • S-85 - Continental TME27 Models (CE)
- Ground Control Box, S-80 • S-85 - Continental TME27 Models (CE)
- Platform Control Box, S-80 • S-85 - Continental TME27 Models (CE)
- Electrical Schematics, S-80, S-85 – AS Models
- Electrical Schematic, S-80 • S-85 - Deutz TD2011L04i Models (AS)
- Ground Control Box, S-80 • S-85 - Deutz TD2011L04i Models (AS)
- Platform Control Box, S-80 • S-85 - Deutz TD2011L04i Models (AS)
- Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (AS)
- Ground Control Box, S-80 • S-85 - Perkins 804D-33 Models (AS)
- Platform Control Box, S-80 • S-85 - Perkins 804D-33 Models (AS)
- Electrical Schematic, S-80 • S-85 - Continental TME27 Models (AS)
- Ground Control Box, S-80 • S-85 - Continental TME27 Models (AS)
- Platform Control Box, S-80 • S-85 - Continental TME27 Models (AS)
- Schematics - Options
- Continental Options Schematic
- Deutz and Perkins Options Schematic
- Platform Level Cutout, CTE Option
- kW Hydraulic Generator Wiring Diagram
- kW Hydraulic Generator Electrical Schematic
- Belt Driven Generator Option
- Hydraulic Schematics
- Hydraulic Schematic, 2WD Models
- Hydraulic Schematic, 4WD Models
|
September 2015 Service and Repair ManualPlatform ControlsPart No. 1269074 S-80 • S-85 • S-80X 19How to Adj ust the Joystick Max- out SettingHow to Adjust the JoystickMax-out SettingThe max-out setting of a joystick controls themaximum speed of a joystick-controlled machinefunction. Whenever a hydraulic cylinder, drivemotor or hydraulic pump is replaced, the max-outsetting should be adjusted to maintain optimumperformance. The max-out settings on the joystickcan be changed to compensate for hydraulic pumpwear to maintain peak performance from themachine.Note: Perform this procedure with the boom in thestowed position.1 Pull out the red Emergency Stop button to theon position at both the ground and platformcontrols.2 Turn the key switch to platform control. Do notstart the engine.3 Push in the platform controls red EmergencyStop button to the off position.4 Do not press down the foot switch.5 Move and hold the drive enable toggle switchin the right position and pull out the redEmergency Stop button to the on position.6 When the alarm sounds, release the driveenable toggle switch.7 Momentarily activate the drive enable toggleswitch in the right direction 4 times.Result: There should be a pause and thealarm should sound 4 times indicating that themachine is in max-out calibration mode.Result: The alarm does not sound. Repeatsteps 3 through 7.8 Start the engine from the platform controlsand press down the foot switch.9 Start a timer and activate the machinefunction that needs to be adjusted. Record thetime it takes for that function to complete a fullcycle (ie; boom up).10 Compare the machine function time with thefunction times listed in Refer to Specifications,Performance Specifications. Determinewhether the function time needs to increase ordecrease.11 While the joystick is activated, adjust themax-out setting to achieve the proper functioncycle time. Momentarily move the driveenable toggle switch in the right direction toincrease the function speed or momentarilymove the drive enable toggle switch in the leftdirection to decrease the function speed.Note: Each time the drive enable toggle switch ismomentarily moved, the function speed willchange in 2% increments from a default of 100%,with a minimum of 60% and a maximum of 120%.12 Repeat steps 9 through 11 for each joystickcontrolled machine function.13 Return the joystick to the neutral position andwait for approximately 10 seconds to allow thesettings to be saved.Result: The alarm should sound indicatingthat the settings have been saved in memory.Note: Do not operate any machine function duringthe 10 second waiting time.Function speeds (factory settings)Boom up 89 to 93 secondsBoom down 90 to 94 secondsBoom extend 73 to 79 secondsBoom retract 79 to 84 secondsTurntable rotate, 360°boom fullystowed95 to 103 secondsDrive speeds (factory settings)Stowed- high speed 7.9 to 8.5 secondsNon-stowed 40 to 45 seconds
|
