Contents - September
- safety rules
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Specifications
- Performance Specifications
- Hydraulic Component Specifications
- Manifold Component Specifications
- Machine Torque Specifications
- Hydraulic Hose and Fitting Torque Specifications
- Torque Procedure
- Section 3 Repair Procedures
- repair procedures
- Platform Controls
- Joysticks
- How to Adjust the Joystick Max-out Setting
- How to Adjust the Joystick Ramp Rate Setting
- How to Adjust the Joystick Threshold Setting
- How to Calibrate the Boom Angle Sensor
- Platform Components
- Platform Leveling Slave Cylinder
- Platform Rotator
- How to Bleed the Platform Rotator
- Platform Overload System
- Jib Boom Components
- Jib Boom Lift Cylinder
- Boom Components
- How to Repair the Cable Track
- How to Remove the Boom
- Boom Lift Cylinder
- Boom Extension Cylinder
- Boom Extend/Retract Cables
- How to Replace the Boom Extend/Retract Cables
- Platform Leveling Master Cylinder
- Engines
- How to Install the Flex Plate
- How to install the Pump and Bell Housing Assembly
- Ground Controls
- Hydraulic Pumps
- Drive Pump
- How to Prime the Pump
- Valve Adjustments - Function Manifold
- How to Adjust the Boom Extend Relief Valve
- Brake/Two-Speed Manifold Components
- Turntable Rotation Manifold Components
- Platform Rotate Manifold Components
- Platform Manifold Components, S-80
- Platform Manifold Components, S-85
- WD Traction Manifold Components
- Drive Oil Diverter Manifold Components (welder option)
- Valve Adjustments - Traction Manifold
- Valve Coils
- How to Test a Coil Diode
- Fuel and Hydraulic Tanks
- Hydraulic Tank
- Turntable Rotation Components
- How to Remove the Turntable Rotation Hydraulic Motor
- How to Adjust the Turntable Rotation Gear Backlash
- Steer Axle Components
- Drive Motors
- Steer Cylinders
- Non-steer Axle Components
- Oscillating Axle Components
- Oscillate Directional Valve
- How to Set Up the Directional Valve Linkage
- Section 4 Fault Codes
- Control System Fault Codes
- Fault Code Display - Deutz and Perkins Models
- Fault Code Display - Flashing and Solid LED's Deutz D 2.9 L4 and Perkins 404F-22 Models
- Soft Key Functions and Icons Deutz D 2.9 L4 and Perkins 404F-22 Models
- Main Menu Structure - Deutz D 2.9 L4 Models
- Main Menu Structure - Perkins 404F-22 Models
- Deutz D 2.9 L4 Engine Fault Codes
- Perkins 404F-22 Engine Fault Codes
- Continental TME27 Engine Fault Codes
- Section 5 Schematics
- Electrical Symbol Legend
- Hydraulic Symbols Legend
- Relay and Fuse Panel Legend - Deutz TD2011L04i
- Relay and Fuse Panel Legend - Perkins 804D-33
- Connector Pin Legends
- Continental TME27 Engine Harness
- S-80X Ground Control Box Wiring Diagram
- Deutz TD2.9 L4 Engine Harness
- Perkins 404F-22T Engine Harness
- Electrical Schematics, S-80X – ANSI and CSA Models
- Electrical Schematic, S-80X - Deutz TD2.9 L4 Models (ANSI / CSA)
- Ground Control Box, S-80X - Deutz TD2.9 L4 Models (ANSI / CSA)
- Platform Control Box, S-80X - Deutz TD2.9 L4 Models (ANSI / CSA)
- Electrical Schematic, S-80X - Deutz TD2011L04i Models (ANSI / CSA)
- Ground Control Box, S-80X - Deutz TD2011L04i Models (ANSI / CSA)
- Platform Control Box, S-80X - Deutz TD2011L04i Models (ANSI / CSA)
- Electrical Schematic, S-80X - Perkins 404F-22T Models (ANSI / CSA)
- Ground Control Box, S-80X - Perkins 404F-22T Models (ANSI / CSA)
- Platform Control Box, S-80X - Perkins 404F-22T Models (ANSI / CSA)
- Electrical Schematic, S-80X - Perkins 804D-33 Models (ANSI / CSA)
- Ground Control Box, S-80X - Perkins 804D-33 Models (ANSI / CSA)
- Platform Control Box, S-80X - Perkins 804D-33 Models (ANSI / CSA)
- Electrical Schematic, S-80X - Continental TME27 Models (ANSI / CSA)
- Ground Control Box, S-80X - Continental TME27 Models (ANSI / CSA)
- Platform Control Box, S-80X - Continental TME27 Models (ANSI / CSA)
- Electrical Schematics, S-80, S-85 – ANSI and CSA Models
- Deutz TD2.9 L4 Models (ANSI / CSA)
- Ground Control Box, S-80 • S
- Platform Control Box, S-80 • S
- Electrical Schematic, S-80 • S
- Deutz TD2011L04i Models (ANSI / CSA)
- Perkins 404F-22T Models (ANSI / CSA)
- Perkins 804D-33 Models (ANSI / CSA)
- Continental TME27 Models (ANSI / CSA)
- Electrical Schematics, S-80, S-85 – CE Models
- Electrical Schematic, S-80 • S-85 - Deutz TD2.9 L4 Models (CE)
- Ground Control Box, S-80 • S-85 - Deutz TD2.9 L4 Models (CE)
- Platform Control Box, S-80 • S-85 - Deutz TD2.9 L4 Models (CE)
- Electrical Schematic, S-80 • S-85 - Deutz TD2011L04i Models (CE)
- Ground Control Box, S-80 • S-85 - Deutz TD2011L04i Models (CE)
- Platform Control Box, S-80 • S-85 - Deutz TD2011L04i Models (CE)
- Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (CE)
- Ground Control Box, S-80 • S-85 - Perkins 804D-33 Models (CE)
- Platform Control Box, S-80 • S-85 - Perkins 804D-33 Models (CE)
- Electrical Schematic, S-80 • S-85 - Continental TME27 Models (CE)
- Ground Control Box, S-80 • S-85 - Continental TME27 Models (CE)
- Platform Control Box, S-80 • S-85 - Continental TME27 Models (CE)
- Electrical Schematics, S-80, S-85 – AS Models
- Electrical Schematic, S-80 • S-85 - Deutz TD2011L04i Models (AS)
- Ground Control Box, S-80 • S-85 - Deutz TD2011L04i Models (AS)
- Platform Control Box, S-80 • S-85 - Deutz TD2011L04i Models (AS)
- Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (AS)
- Ground Control Box, S-80 • S-85 - Perkins 804D-33 Models (AS)
- Platform Control Box, S-80 • S-85 - Perkins 804D-33 Models (AS)
- Electrical Schematic, S-80 • S-85 - Continental TME27 Models (AS)
- Ground Control Box, S-80 • S-85 - Continental TME27 Models (AS)
- Platform Control Box, S-80 • S-85 - Continental TME27 Models (AS)
- Schematics - Options
- Continental Options Schematic
- Deutz and Perkins Options Schematic
- Platform Level Cutout, CTE Option
- kW Hydraulic Generator Wiring Diagram
- kW Hydraulic Generator Electrical Schematic
- Belt Driven Generator Option
- Hydraulic Schematics
- Hydraulic Schematic, 2WD Models
- Hydraulic Schematic, 4WD Models
|
September 2015 Service and Repair ManualBoom ComponentsPart No. 1269074 S-80 • S-85 • S-80X 35How to R epair the C abl e Tr ackHow to Repair the Cable TrackComponent damage hazard.The boom cable track can bedamaged if it is twisted.Note: A cable track repair kit is available throughGenie Service Parts, part no. 77896. The kitincludes a 4-link section of cable track.1 Visually inspect the cable track and determinewhich 4 link section needs to be replaced.2 Carefully remove the snap rings from eachend of the damaged section of cable track.3 Remove the retaining fasteners from theupper black rollers from the 4-link section ofcable track to be replaced. Remove therollers.4 Lift up the hoses and cables and carefullyremove the damaged 4-link section of cabletrack.Component damage hazard.Hoses and cables can bedamaged if they are kinked orpinched.5 Remove the upper rollers from thereplacement section of cable track.6 Lift up the hoses and cables and carefullyinsert the new 4 link section of cable track.Component damage hazard.Hoses and cables can bedamaged if they are kinked orpinched.7 Connect the ends of the replacement cabletrack section to the existing cable track usingthe snap rings.8 Install the rollers onto the new section of cabletrack.9 Operate the boom extend/retract functionthrough a full cycle to ensure smoothoperation of the new section of cable track.4-2 Boom4-2BoomHow to Shim the BoomHow to Shim the Boom1 Measure each wear pad.Boom wear pad specificationsBoom number one MinimumBottom wear pads(extension end of boom)0.50 inch12.7 mmTop and side wear pads(extension end of boom)0.625 inch15.9 mmBoom number twoTop, bottom and side wear pads(extension end of boom)0.50 inch12.7 mmBottom wear pads(pivot end of boom)0.50 inch12.7 mmTop and side wear pads(pivot end of boom)0.625 inch15.9 mmBoom number threeTop, bottom and side wear pads(pivot end of boom)0.50 inch12.7 mmNote: Replace the pad if thickness is less thanminimum specification. If thickness is more thanminimum specification, perform the followingprocedure.2 Extend the boom until the wear pads areaccessible.3 Loosen the wear pad mounting fasteners.4 Install the new shims under the wear pad toobtain zero clearance and zero drag.5 Tighten the mounting fasteners.6 Extend and retract the boom through an entirecycle. Check for tight spots that could causebinding or scraping.Note: Always maintain squareness between theouter and inner boom tubes.
|
