Contents - April
- safety rules
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- specifications
- Machine Component Weights
- Performance Specifications
- Hydraulic Component Specifications
- machine torque specifications
- Hydraulic Hose and Fitting Torque Specifications
- Torque Procedure
- Scheduled Maintenance Procedures
- Pre-Delivery Preparation Report
- maintenance inspection report
- Checklist A Procedures
- A-2 Perform Pre-operation Inspection
- A-4 Perform 30 Day Service
- A-6 Replace the Drive Hub Oil
- Checklist B Procedures
- B-2 Inspect the Electrical Wiring
- B-3 Inspect the Tires, Wheels and Lug Nut Torque
- B-4 Confirm the Proper Brake Configuration
- B-6 Test the Ground Control Override
- B-8 Test the Drive Brakes
- B-10 Test the Drive Speed - Raised or Extended Position
- B-11 Test the Alarm Package (if equipped)
- B-12 Test the Turntable Rotation Stop
- B-14 Perform Hydraulic Oil Analysis
- Checklist C Procedures
- Checklist D Procedures
- D-2 Check the Free-wheel Configuration
- D-3 Check the Turntable Rotation Bearing Bolts
- D-4 Replace the Drive Hub Oil
- D-6 Inspect for Turntable Bearing Wear
- Checklist E Procedures
- E-2 Grease the Steer Axle Wheel Bearings
- repair procedures
- platform controls
- platform components
- platform rotator
- platform overload system
- jib boom
- Jib Boom Bell Crank (models without rotating jib boom)
- jib boom lift cylinder
- primary boom components
- Primary Boom
- How to Disassemble the Primary Boom
- primary boom lift cylinder
- boom extension cylinder
- Platform Leveling Master Cylinder
- secondary boom components
- Secondary Boom
- secondary boom lift cylinder
- hydraulic pump
- function manifold components
- Valve Adjustments - Function Manifold
- How to Adjust the Secondary Boom Down Relief Valve
- How to Adjust the Turntable Rotate Relief Valve
- Jib Boom and Platform / Jib Boom Rotate Manifold Components
- valve coils
- How to Test a Coil Diode
- turntable rotation components
- Steer Axle Components
- Non-steer Axle Components
- fault codes
- Fault Code Charts
- Section 6 Schematics
- Electrical Symbol Legend
- hydraulic symbols legend
- limit switch location legend
- Power Cable Wiring Diagram
- Drive Contactor Panel Wiring Diagram
- Manifold and Limit Switch Wiring Diagram
- LVI/BCI Option Wiring Diagram
- Work and Drive Lights Option
- CTE Option, (CE Models)
- Charger Interlock Option
- Hydraulic Schematics
- hydraulic schematic
- Ground Control Box Terminal Strip Wiring Diagram, (ANSI / CSA / AS), (before serial numbers Z3010-12119, Z34N10-8857 and Z3410-7774)
- Ground Control Box Switch Panel Wiring Diagram, (ANSI / CSA / AS), (before serial numbers Z30N10-12119, Z34N10-8857 and Z3410-7774)
- Platform Control Box Wiring Diagram, (ANSI / CSA / AS), (before serial numbers Z30N10-12119, Z34N10-8857 and Z3410-7774)
- Ground Control Box Terminal Strip Wiring Diagram, (CE), (before serial numbers Z30N10-12119, Z34N10-8857 and Z3410-7774)
- Ground Control Box Switch Panel Wiring Diagram, (CE), (before serial numbers Z30N10-12119, Z34N10-8857 and Z3410-7774)
- Platform Control Box Wiring Diagram, (CE), (before serial numbers Z30N10-12119, Z34N10-8857 and Z3410-7774)
- Ground Control Box Switch Panel Wiring Diagram, (ANSI / CSA), (from serial numbers Z30N10-12119, Z34N10-8857 and Z3410-7774)
- Platform Control Box Wiring Diagram, (ANSI / CSA), (from serial numbers Z30N10-12119, Z34N10-8857 and Z3410-7774)
- Z34N14-10983 and Z3414-9685
|
April 2016 Service ManualChecklist E ProceduresPart No. 139378 Z-30/20N • Z-30/20N RJ • Z-34/22 • Z-34/22N 4312 Install the hydraulic tank on the machine.Install the hydraulic tank mounting fastenersand torque them to 8 ft-lbs / 10.8 Nm.Component damage hazard.The hydraulic tank is plastic andmay become damaged if thetank mounting fasteners areover tightened.13 Install the hydraulic hoses.14 Fill the tank with hydraulic oil until the fluid iswithin the full and add marks on the hydraulictank. Do not overfill. Refer to Specifications,Machine Specifications.15 Clean up any oil that may have spilled.Properly discard of used oil.16 Open the hydraulic tank shutoff valve.Component damage hazard. Besure to open the hydraulic tankshutoff valve after installing thehydraulic tank.E-2Grease the Steer Axle WheelBearings, 2WD ModelsGenie specifications require that this procedure beperformed every 2000 hours or every two years,whichever comes first.Perform this procedure more often if dustyconditions exist.Maintaining the steer axle wheel bearings isessential for safe machine operation and servicelife. Operating the machine with loose or wornwheel bearings may cause an unsafe operatingcondition and continued use may result incomponent damage. Extremely wet or dirtyconditions or regular steam cleaning and pressurewashing of the machine may require that thisprocedure be performed more often.1 Loosen the wheel lug nuts. Do not removethem.2 Block the non-steer wheels, then center alifting jack under the steer axle.3 Raise the machine 6 inches / 15 cm and placeblocks under the drive chassis for support.4 Remove the lug nuts. Remove the tire andwheel assembly.5 Check for wheel bearing wear by attempting tomove the wheel hub side to side, then up anddown.Result: There should be no side to side or upand down movement.Skip to step 10 if there is no movement.
|
