Kenwood KDC-BT92SD Instruction Manual

Also see for KDC-BT92SD: Manual Service manual

41 | KDC-BT92SD English | 42Clock and Other FunctionsTheft Deterrent FaceplateThe faceplate of the unit can be detached andtaken with you, helping to deter theft.Removing the Faceplate1 Press the Release button.Drop open the faceplate.2 Drawing the faceplate to left side pull it toforward and remove it.¤• The faceplate is a precision piece of equipment and canbe damaged by shocks or jolts.• Keep the faceplate in its faceplate case while detached.• Do not expose the faceplate (and the faceplate case) todirect sunlight or excessive heat or humidity. Also avoidplaces with too much dust or the possibility of watersplashing.Reattaching the Faceplate1 Align the shaft on the unit with the depressionon the faceplate.2 Push the faceplate in until it clicks.The faceplate is locked in place, allowing you touse the unit.Initial SettingsYou can select following Initial Setting items.1 Select the StandbyPressing the [SRC] button repeatedly switchessource.Select the “STANDBY” display.✍ SRC Select mode 2: Press the [SRC] button andthen turn the [VOL] knob. To determine theselected source, press the [VOL] knob.2 Enter Menu List modePress the [MENU] button.3 Enter Initial Setting modeTurn the [VOL] knob and press it when thedesired item is displayed.Select “Initial Settings”.4 Select the setting item to adjustTurn the [VOL] knob.Display Overview“Initial Settings”“SRC Select” Sets the source selection method.“Settings 1”/ “2”“Beep” Setting the operation check sound (beep sound)ON/OFF.“OFF”/ “ON”“Russian” When this is set to ON, the following characterstrings are displayed in Russian:Folder name/ File name/ Song title/ Artistname/ Album name“OFF”/ “ON”“Menu Language” You can select the display language for theMenu list item.“English”/ “Français”/ ”Español”/ “Deutsch”/“Italiano”/ “Pyccкий”“Power OFF Wait” Setting the timer to turn this unit’s power OFFautomatically when Standby mode continues.Using this setting can save the vehicle’s batterypower.“-----”/: Power OFF Timer function is OFF.“20min”/ “40min”/ “60min”: Turns the powerOFF after minutes.“Built in AUX” When this is set to ON, AUX source can beselected.“ON”: Allows AUX source to be selected. Usethis setting when the built-in AUX terminalis connected to the external equipment allthe time.“OFF”: Disable AUX source selection. Use thissetting when the built-in AUX terminal isnot used.“Forced CD-DA” Sets the CD read mode.“Settings 1”: Automatically distinguishesbetween audio file disc and music CD whenplaying disc.“Settings 2”: Forces playing as music CD.“Built in AMP” Selecting “OFF” turns off the built-in amplifier.Turning off the built-in amplifier improves thequality of the sound from Preout.“OFF”/ “ON”“DSI” DSI (Disabled System Indicator) of the unit blinkswhen the faceplate is removed.“OFF”/ “ON”“F/W Update” Updates the firmware. The update informationwill be posted on the following URL asnecessary.www.kenwood.com/cs/ce/( : Factory setting)5 Make a settingTurn the [VOL] knob to select a setting value,and then press the [VOL] knob.6 Exit Menu List modePress the [MENU] button for at least 1 second,and then press it again briefly.Demonstration mode SettingTurning the demonstration mode ON/OFF.1 Enter Menu List modePress the [MENU] button.2 Enter Demonstration mode settingTurn the [VOL] knob and press it when thedesired item is displayed.Select “DEMO Mode”.3 Set the Demonstration modeTurn the [VOL] knob and press it when thedesired item is displayed.Select “ON” or “OFF”.4 Exit Menu List modePress the [MENU] button.