49 | KDC-BT92SD English | 50DSP SetupListening Position Fine AdjustmentsAdjusting fine tuning of the speaker positioncompensation value specified at Selection> (page 47).Display Item Range“FRONT” Front speaker 0 – 610 cm“REAR” Rear speaker 0 – 610 cm“SW” Subwoofer 0 – 610 cm( : Factory setting)1 Select the sourcePressing the [SRC] button repeatedly switchessource.Select a source other than “STANDBY”.✍ SRC Select mode 2: Press the [SRC] button andthen turn the [VOL] knob. To determine theselected source, press the [VOL] knob.2 Enter Audio Control modePress the [VOL] knob.3 Enter Manual position setting modeTurn the [VOL] knob and press it when thedesired item is displayed.Select “Pro Setup” > “DTA Settings” > “DTA”.4 Select the speaker you want to setTurn the [VOL] knob and press it when thedesired value is displayed.Item Setting overview“DTA FRONT” / “L” Front Left speaker“DTA FRONT” / “R” Front Right speaker“DTA REAR” / “L” Rear Left speaker“DTA REAR” / “R” Rear Right speaker“DTA SW / “L” Subwoofer Left“DTA SW” / “R” Subwoofer Right5 Set the valueTurn the [VOL] knob to select a setting value,and then press the [VOL] knob.The settings of the delay time are automaticallyidentified and compensated by specifying thedistances of each speaker from the center of thevehicle interior.1 Set the front and rear positions and the heightof the reference point to the position of the earsof the person sitting in the front seat, and setthe right and left positions to the center of thevehicle interior.2 Measure the distances from the reference pointto the speakers.Listening Position SelectionThe sound environment can be compensated inaccordance with the selected position. According tothe listening position, select the position from thefollowing settings.Display Compensation seat“ALL” Not compensating.“Front-Left” Front-Left seat“Front-Right” Front-Right seat“Front” Front seat( : Factory setting)1 Select the sourcePressing the [SRC] button repeatedly switchessource.Select a source other than “STANDBY”.✍ SRC Select mode 2: Press the [SRC] button andthen turn the [VOL] knob. To determine theselected source, press the [VOL] knob.2 Enter Audio Control modePress the [VOL] knob.3 Enter Preset position setting modeTurn the [VOL] knob and press it when thedesired item is displayed.Select “Pro Setup” > “DTA Settings” > “PresetPosition”.4 Select the seat you want to compensateTurn the [VOL] knob to select a setting value,and then press the [VOL] knob.5 Exit Audio Control modePress the [MENU] button for at least 1 second.3 Calculate the distance difference in accordancewith the farthest speaker.Reference pointFRONTFRONTSUB-WREARREAR6 Exit Audio Control modePress the [MENU] button for at least 1 second.Channel Level Fine AdjustmentsAfter DTA compensation, you can finely adjustthe unsatisfactory speaker volume of respectivespeaker.Display Item Range“FRONT” Front speaker “–8” — “0”“REAR” Rear speaker “–8” — “0”“SUBWOOFER” Subwoofer “–8” — “0”( : Factory setting)1 Select the sourcePressing the [SRC] button repeatedly switchessource.Select a source other than “STANDBY”.✍ SRC Select mode 2: Press the [SRC] button andthen turn the [VOL] knob. To determine theselected source, press the [VOL] knob.2 Enter Audio Control modePress the [VOL] knob.3 Enter Channel Level setting modeTurn the [VOL] knob and press it when thedesired item is displayed.Select “Pro Setup” > “DTA Settings” > “ChannelLevel”.4 Select the speaker you want to setTurn the [VOL] knob and press it when thedesired value is displayed.Item Setting overview“CHANNEL LEVEL.FRONT” / “L”Front Left speaker“CHANNEL LEVEL.FRONT” / “R”Front Right speaker“CHANNEL LEVEL.REAR” / “L”Rear Left speaker“CHANNEL LEVEL.REAR” / “R”Rear Right speaker“CHANNEL LEVEL.SUBWOOFER” / “L”Subwoofer Left“CHANNEL LEVEL.SUBWOOFER / “R”Subwoofer Right5 Set the valueTurn the [VOL] knob to select a setting value,and then press the [VOL] knob.6 Exit Audio Control modePress the [MENU] button for at least 1 second.
