47 | KDC-BT92SD English | 48DSP SetupCar Type SelectionYou can compensate the delay of the sound arrivaltime by selecting your environment from thefollowing car types.Display Overview“OFF” Not compensating.“Compact” Compact car“Sedan” Sedan“Wagon” Station wagon“Minivan” Minivan“SUV” Sport-utility vehicle“Passenger Van” Passenger van( : Factory setting)1 Select the sourcePressing the [SRC] button repeatedly switchessource.Select a source other than “STANDBY”.✍ SRC Select mode 2: Press the [SRC] button andthen turn the [VOL] knob. To determine theselected source, press the [VOL] knob.2 Enter Audio Control modePress the [VOL] knob.3 Enter Car Type select modeTurn the [VOL] knob and press it when thedesired item is displayed.Select “Pro Setup” > “Car Type”.4 Select the car typeTurn the [VOL] knob.5 Set the valuePress the [VOL] button.6 Exit Audio Control modePress the [MENU] button for at least 1 second.⁄• You can compensate the distances in more details byusing Position Fine Adjustments> (page 49)function.Speaker SettingThe speaker X’Over is automatically set when theposition and size of each speaker are selected fromthe following items.Speaker Item Range“Front” “SIZE” Speaker Size Front“O.E.M.”, “8cm”, “10cm”, “12cm”,“13cm”, “16cm”, “17cm”, “18cm”, “4x6”,“5x7”, “6x8”, “6x9”, “7x10”“LOCATION” Speaker Location Front“Door”, “On Dash”, “Under Dash”“TWEETER” Speaker Range Tweeter“None”, “Small”, “Middle”, “Large”“Rear” “SIZE” Speaker Size Rear“None”, “O.E.M.”, “8cm”, “10cm”, “12cm”,“13cm”, “16cm”, “17cm”, “18cm”, “4x6”,“5x7”, “6x8”, “6x9”, “7x10”“LOCATION” Speaker Location Rear• “Door”, “Rear Deck”• “2nd Row”, “3rd Row” (Car Type:“Minivan”, “Passenger Van”)“SubWoofer” “SIZE” Speaker Size Subwoofer“None”, “16cm”, “20cm”, “25cm”,“30cm”, “38cm Over”( : Factory setting)1 Select the sourcePressing the [SRC] button repeatedly switchessource.Select a source other than “STANDBY”.✍ SRC Select mode 2: Press the [SRC] button andthen turn the [VOL] knob. To determine theselected source, press the [VOL] knob.2 Enter Audio Control modePress the [VOL] knob.3 Enter Speaker setting modeTurn the [VOL] knob and press it when thedesired item is displayed.Select “Pro Setup” > “Speaker Setting”.4 Select the setting item to adjustTurn the [VOL] knob and press it when thedesired item is displayed.5 Make a settingTurn the [VOL] knob to select a setting value,and then press the [VOL] knob.6 Exit Audio Control modePress the [MENU] button for at least 1 second.SRC4MENU VOL¢4 Select the speaker you want to setTurn the [VOL] knob and press it when thedesired item is displayed.Select “Front”, “Rear”, “SubWoofer” or “Tweeter”.5 Select the setting item to adjustTurn the [VOL] knob and press it when thedesired item is displayed.6 Make a settingTurn the [VOL] knob to select a setting value,and then press the [VOL] knob.7 Repeat steps 4 to 6 to complete the X’Oversettings.8 Exit Audio Control modePress the [MENU] button for at least 1 second.X’Over SettingFine adjusting the following setting valuescorresponding to the X’Over values set in thesection (page 47).Display Item Range“X’Over”“Front” “FC” Front High Pass FilterThrough, 30, 40, 50, 60, 70, 80, 90,100, 120, 150, 180, 220, 250 (Hz)“SLOPE” Front High Pass Slope-6, -12, -18, -24 dB/Oct“GAIN” Front Gain0, -1, -2, -3, -4, -5, -6, -7, -8 dB“Rear” “FC” Rear High Pass FilterThrough, 30, 40, 50, 60, 70, 80, 90,100, 120, 150, 180, 220, 250 (Hz)“SLOPE” Rear High Pass Slope-6, -12, -18, -24 dB/Oct“GAIN” Rear Gain0, -1, -2, -3, -4, -5, -6, -7, -8 dB“SubWoofer” “FC” Subwoofer Low Pass Filter30, 40, 50, 60, 70, 80, 90, 100, 120,150, 180, 220, 250, Through (Hz)“SLOPE” Subwoofer Slope-6, -12, -18, -24 dB/Oct“GAIN” Subwoofer Gain0, -1, -2, -3, -4, -5, -6, -7, -8 dB“PHASE” Subwoofer PhaseReverse (180°)/ Normal (0°)“Tweeter” “FC” Tweeter High Pass Filter1, 1.6, 2.5, 4, 5, 6.3, 8, 10, 12.5 (kHz)“Volume” Tweete Volume0, -1, -2, -3, -4, -5, -6, -7, -8 dB( : Factory setting)1 Select the sourcePressing the [SRC] button repeatedly switchessource.Select a source other than “STANDBY”.✍ SRC Select mode 2: Press the [SRC] button andthen turn the [VOL] knob. To determine theselected source, press the [VOL] knob.2 Enter Audio Control modePress the [VOL] knob.3 Enter X’Over setting modeTurn the [VOL] knob and press it when thedesired item is displayed.Select “Pro Setup” > “X’Over”.
