Kenwood KDC-X8019BT Instruction Manual

Also see for KDC-X8019BT: Service manual Quick start guide

Contents

English | 35Audio Adjustments“Sound Elevation” Virtually raises the sound field usingthe DSP.“OFF”/ “Low”/ “Middle”/ “High”“Volume offset” Sets each source’s volume as a differencefrom the basic volume.“–8” — “0” (AUX: “–8”— “+8”)“Rear Mute”*2 Sets the Rear channel Mute.“ON”/ “OFF”“SubWoofer Mute”/“Woofer Mute”* 1Sets the Subwoofer Mute.“ON”/ “OFF”“Preset”*1 Sets the audio preset.- Audio Preset Memory (page 42).- Audio Preset Recall (page 43).“Bass Boost”* 1 Sets the Bass Boost level in 3 steps.“OFF”/ “Level1”/ “Level2”/ “Level3”“Loudness”*1 Makes the sounds at high and lowfrequencies louder.“OFF”/ “Low”/ “High”“Balance”/ “Fader”*2 Adjusts left/right and front/rear speakerbalance.(Left) “L15” — “0” — “R15” (Right)(Rear) “R15” — “0” — “F15” (Front)*1( : Factory setting)*1 This setting can be made when “2 Zone” (Dual ZoneSystem) is set to ON.*2 This setting cannot be made when the speaker system isconnected in the 3-way mode.1 Select the sourcePressing the [SRC] button repeatedly switchessource.Select a source other than “STANDBY”.✍ SRC Select mode 2: Press the [SRC] button andthen turn the [VOL] knob. To determine theselected source, press the [VOL] knob.2 Enter Audio Control modePress the [VOL] knob.3 Select the setting item to adjustTurn the [VOL] knob and press it when thedesired item is displayed.4 Make a settingTurn the [VOL] knob to select a setting value,and then press the [VOL] knob.5 Exit Audio Control modePress the [MENU] button for at least 1 second.Remarks• DSP SetWhen “DSP Set” is set to “Bypass”, the DSP function isdisabled , and the colored items can not be set.Audio ControlYou can adjust following Audio Setting items.Display Overview“SubWoofer Level”/“Woofer Level”* 1You can set subwoofer level.“–15” — “0” — “+15”“Preset Equalizer”* 1 Sets the sound quality.- Preset Equalizer curve Select (page36).“Manual Equalizer”* 1 Sets the sound quality.- Manual Equalizer Control (page 36).“Pro Setup”“DSP Set”* 1*2 “Bypass”: Disables the DSP function.“Through”: Enables the DSP function.“Car Type”* 1 To get clear sound, set the soundenvironment according to the location andsize of physically installed speakers withreference to the followings:- Car Type Selection (page 38).- Speaker Setting (page 38).- X’Over Setting (page 39).- Listening Position Selection (page40).- Listening Position Fine Adjustments(page 40).- Channel Level Fine Adjustments (page41).“Speaker Setting”* 1“X’Over”*1“DTA Setting”* 1“Zone Control”*2 Sets the Dual Zone System.- Dual Zone System (page 37).“SoundEnhancements”*1“Supreme” Turns ON/OFF the Supreme function.Can be set while Audio file source of USB/SD/CD and iPod source.“ON”/ “OFF”“HIGWAY-SOUND” Compensates the low volume or basssound being lost by road noises to makevocal sound clearer.“OFF”/ “Low”/ “Middle”/ “High”“Space Enhancer” Virtually enhances the sound space usingthe DSP.“OFF”/ “Small”/ “Medium”/ “Large”“Sound Realizer” Virtually makes the sound more realisticusing the DSP.“OFF”/ “Level1”/ “Level2”/ “Level3”SRC4VOL¢38MENU VOLNext page 3