Kenwood KRF-V8881 D Instruction Manual

Contents

VR-2OSO/VR-2OSO/KRF-VS881DiKRF+V7771[3[En/K)When recording sound with a recorder component of KENWOOD, synchro recording is possible by setting the INPUT SELECTORto select "Tape1" or "MD" according to the connected component.Recording a music sourceO Select the recording source.The icons differ accordingto the setup of +Setup IR"etc.19 Put the MD recorder or cassette deck to record-pause mode.Select the "Remote Mode" icon from the fixed segments._+ Select the "MD/Tapel" icon,Select the MD or cassette deck control icon and put it torecord-pause mode+O Play the source and record it.a When the "Remote Mode" con is selected, the icons of thecomponents assigned to the inputS, such as the "CD1 ", "Video 1","Video2", "Video3" and "MD/Tapel" icons bnk for a fewseconds+By select;nO a bI+nkng icon, the selected component can becontroled without switching the input selector (The "RemoteMode" con can be used to put the recording component to pausemode w thout switching the input selectoryWhen an icon that is not blinking is selected, the input selector isswitched automat sally• For the recerding procedure of the MD recorder or cassette oeck,refer to its instruction menusCopying tape (TAPE1 --_ TAPE2) lO Select the "MD/Tapel" input. |O Startplayback of the cassette deck connected to the MD/TAPE1]input jacks, then start recording of that connected to the CD2/TAPE2 MONITOR input jacks+Caution for recordingDigital--* digital recordingThe digital signal input through DIGITAL IN is output digitally atthe OPTICAL jack+Make sure the following points to record a digital signal inputinto the receiver. (The DTS and Dolby Digital (AC-3} signals can-not be recorded,)Igl Connect the digital output from the source component to thedigital input of the receiverO Connect the digital output (OPTICAL jack) of the receiver to thedigital input (OPTICAL jack} of the MD recorder.O Record the signal on the recorder component (MD recorderlDigital-* analog recordingBy reproducing the digital signal input to the receiver in stereo(surround mode), the signal can be recorded in analog with thefollowing procedure,O Set up the recorder component +eady for recordingt_ Select the receiver's input to the source component,_) Play the desired software.O Set the "Input Digital" icon from "Auto" to "Manual",O In the "Lstn Mode'* menu screen, select the "Stereo" iconO PFay the software from the beginning and record it.• Do not switch to "CD2/Tape2 (Monitor)" during recording,This may cause the interruption of the recording,Note on CD2/ Tape2 (Monitor)The following operations are made available by setting the "CD2/Tape2 (Monitor)" icon on the "Setup Input" menu screen to"Tape2 (Monitor)", However, remember that these functions are available only when the analog input/output are used, If the"CD2/Tape2" icon in the fixed segments is selected during playback of a digital input, the input is switched to the analog inputand noise may be generated."Tape2 (Monitor)" setup menu screenFor the setup of the remote control unit, p[ease read "Set "CD2/Tape2"",ICONDISPLAY@002 ! TAPE2MONITORUsing "CD2/Tape2"The CD2/TAPE2 MONITOR input jacks of the main unit accept e cassette deck or graphic equalizer.When a graphic eelJalizer is connected, set "CD2]Tape2" to "Tape2" and select the "CD2/Tape2"icon in the fixed segments to on,When a 3+head cassette deck is connected to the CD2iTAPE2 MONITOR _nput jacks, the recordedaudio can be monitored during recording, and turning "CD2/Tape2" on and off allows you tocompare the source audio and recorded audio Refe to the instructio_ manuals of the connectedcomponents for the_ operating procedures,The "CD2/Tape2 (Monitor)" funct+on is not ave Jab e during p ayback of a digital input Se ecting"CD2/Tspe2 (Monitor)" durng dig tal input playback switches the input to the analog input