Kenwood KRF-V8881 D Instruction Manual

Contents

VR*20_OiVR-208Q/KR_ V88Bl O/KRF V7 7710 {En/K]Make connections as shown below.The digital in jacks can accept either DTS, Dolby Digital {AC-3) or PCM (CD Format) signals (the input signal type is detectedautomatically).When connecting the related system components, be sure to also refer to the instruction manuals supplied with thecomponents you are connecting.Do not connect the power cord to a wall outlet until all connections are completed.The connected components are given as examples becausethe available models vary depending on marketing areas.Connect components capable of output-ting Dolby Digital IAC-3) or standard PCMformat digital signals.LASER DISC RF DEMODULATOR (DEM-9991D)Note : ©nlyrequi_edifyouwishtoplayLase_Discsin the Dotby Digital (AC-3) formatTo connect an LD player with a Dolby Digital (AC-3) RF OUT orDIGITAL OUT (Some LD player have a PCM Digital Outputs, in this casethe customer doesn't need the DEM-9991D,)Connect the LD player to the {optional} KENWOOD LASER DISC RFDEMODULATOR (DEM-9991D). Then connect the demodulator tothe DIGITAL IN (VIDEO4 COAXIAL),To connect the digital output from an LD player, connect it either tothe DIGITAL INPUT OPT, (@_Jor DIGITAL INPUT COAX, ((_;) jack.Connect the vdeo signal and analog audio signals to the V_DEO 4. jacks(See "Connecting of video components")ICOAXIAL) [ [_ r°_.,T-Si_7 i""I!I DGITALOUT i| | (OP rlCALIAC3 RF OuTiCOAXIAL) Note : Connect either (_ or :_Should not be corm acted both_mlmQDIGITAL. OUT_%_C©AX/AL)DrGITAL OUT 1_[OPTICAL)To connect an DVD playerwith a DIGITAL OUT=Connect the video signal, S Video signa andanalog audio signals to the same serector(INPUT) jacks,(See "Connecting of video components" )Use either the (i_ {COAXIAL) or _ (OPTICAL) jack for the connection of a DVD player,To the VIDEO 4 COAXIAL jack, connect the input from the DIGITAL OUT (1_ (COAXIAL) jack of a OVD player or the DIGITALOUT (# (COAXIAL) Jack of the DEM-gg91D,LASER DISC RF DEMODULATOR DEM-9991D (Optional)Place the power supply away from the demodulator, receiver,and any antennas.0 POWER switchUse to swtch the POWER OFF/POWER ON tOPTJCOAX,),With the OPT or COAX, position, the input is switched automati-cally to the Dolby Digital (AC-3) RF nput whenever the Dolby Digital(AC-3) RF signal is inpuLPOWER indicatorLghts (red) when the power switch (O) is set to ON (OPT/COAX tRE LOCK indicatorlights when a Dolby Digital (AC-3) RF sgnal is input to the RF INPUT_AC-3 RF INPUT} iack !_t. tThis ir, dicator is extinguished when a digitalinput is in use.)O DIGITAL OUTPUT COAX, (COAXIAL}Connect this jack to the VIDEO4 COAXIAL (DIGITAL }Nt, jack On you_Reeiever It outputs Dolby Digital (AC-3) coaxial digital signets whenthe POWER (O) is set to COAX, and a Dolby Dig tel (AC-3) RF signalis input to the RF tNPbT (AC*3 RE INPUT) iack (_)RF INPUT AC-3 RF (Dolby Digital RF)Connect this jack to the Dolby Dig tat (AC-3) R F OUTPUT jack on yourLD 0layer.DIGITAL INPUT COAX, (COAXIAL)Connect this jack to the COAXIAL OUTPUT iack on yo_,_ LD playerDIGITAL INPUT OPT, (OPTICAL)Connect this iack to the OPTICAL OUTPLJT jack on your LD player,• When there are simuhaneous inputs through the RF iNPUT tAC_3 RE)iack and DIGITAL INPUT jack, the nput through RE INPUT (AC-3 RE) isgiven the p_iodtv,ODC tN 12V jackConnect _hs iack to the AC adaptor suppled witr_ your demodulatorConnect the AC adaptor to a wail outlet after compJeting all of toeother connections.