Kenwood KRF-V8881 D Instruction Manual

Contents

CConec the system control .......... :9Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage ofconvenient system control operations.There are two KENWOOD system control modes. Make connections according to the groups of terminal symbols shownbelow.[_] Mode :lets you corrlbine [_. _(_8]. and _ termina s1"_1]El Mode : for [__]E_] terminals onlyThis unt is compatible with both [X58} and ISL161 modes. It comes from the factory set to the [SL16] mode To switch to the [XS81 mode, fellowthe instructions in "SWITCHING FROM [SL161 TO [XS8]" below.EXAMPLE: [xsa] mode connectionsThe ucderlff_ed pertloll represe_Tts the sett ng ot _he system contlel medeEXAMPLE: [XS16] mode connectionsThe ul_dedined porgon represents the setling of the syslem Control mode[SL16] [xsa] ]Receiver ] [SL16] [xsa] [Receiver ![SL16] IDVD player SYSTEM [SL161 DVD player[SL16] ]MD recorder CONTROL , _ cCO__TROLcord [SL16] I MD recorder _! SYSTEM[SL16] [XS] [X$8] [XR] [Cassette deck j] [ LS_] [XS, [XSa] ,XR, _is_ J.]1..cord.,ayeri] [.ecordp,ayer1• In order to take advantage of the system control operations, the components must be connected to the correct jacks To use a CD player it mustbe connected to the CD jacks. To use a cassette deck (or M D reco_derI it must be connected to the TAPE 1!MD jacks When using more than oneCD player (etc.) only the one connected to the specified iacks may be connected for system control.• Some CD players and cassette decks are net compatible with the [SL16] system control mode. Be sure to use the [XS8] system control modewhen making system connections with equipment that is not ISL16] compatible.m Some MD players are not system-control compatible The system control function is nOt aver able when a MD player e used by connecting ttthrough a d gitaL input You cannot connect the system control cord to this kind of equipment.1. ISL16} equipment cannot be combined with fXR]. [XS]. and IXS8] equipment for system operations. If yourequipment consists of this kind of combination, p_ease de not connect any system control cords. Even -witheutsystem control cords, normat operations can be carried out without effecting performance.2. Do not connect system control cords to any components other than those specified by KENWOOD it maycause a maffunction and damage your equipment.3= Be sure the system control plugs are inserted all the way in to the system control terminals.-SYSTEM CONTROLOPERATIONSRemote ControlLets you operate this unit with the system remote suppliedwith the receiver,Automatic Operation (except [XR] equipment}When you start playback from a source component, the inputselector on this unit switches to that component automati-cally,Synchronized Recording (except [XR] equipment)Lets you synchronize recording with the start of playbackwhen recording from CD, MD or analog discs,SWITCHING FROM [SL 16] TO[XSS]You can easty change the system control mode by adjust ng theposition of [he SYSTEM CONTROL switch on the rear panelDo this operation after completing al! connectionsFor[SL16} SL16 XS8 Forl×Sallr• This operation wilt not effect items stored in the memory• After switching the system controt mode. turn the power off andthen on once to confirm the new sett ngRegistering setup codes for KENWOOD audio components* Once '_,ou finish makir_g the system connections, be sure to register _.he appropriate setup code for each component.• If you own remote controllable KENWOOD audio components that are not compatible with system control be combined with yourother system contro components), registering the setup code enables you to comtro! those components using the remote contlol supp iedwith this u nit (without con nectrng system control cordsI To reg4ster setup codes for your remote controllable KEI'4WOO D audio components.see "Setup for controlling AV components"