Version: 1.01 USA Function Reference (FUNC) 2410 POWER CONTROLThe TKR-750/850/751/851 has various power controlfunctions, such as the Power Save function, a function toswitch the power from the main power to the backuppower, and the operation when turning TKR-750/850/751/851 ON. You can operate a assigned functioninterlocking with Save On/Off, the Start Up operation, anda function to switch the power from the main power andthe backup power.• Save On/Off• Start Up• Backup Power• Main PowerTable 10-1 Available functionsName offunctions Description of functionsNone TKR-750/850/751/851 does not perform anyoperation.AUX Out 1 Off-AUX Out 5 OffThe function assigned to a specified AuxiliaryOutput port is disabled when TKR-750/850/751/851 starts operation.You can assign functions when “Selectable”is configured to the Auxiliary Output 1 -Auxiliary Output 5 ports.(Refer to 20.3 Assigning Functions to theAuxiliary Output Ports.)AUX I/O 1 Off-AUX I/O 6 OffThe function assigned to a specified AuxiliaryI/O port is disabled when TKR-750/850/751/851 starts operation.You can assign functions when “Selectable”is configured to the Auxiliary I/O 1 toAuxiliary I/O 6 ports.(Refer to 20.3 Assigning Functions to theAuxiliary Output Ports.)AUX Out 1 On-AUX Out 5 OnThe function assigned to a specified AuxiliaryOutput port is enabled when TKR-750/850/751/851 starts operation.You can assign functions when “Selectable”is configured to the Auxiliary Output 1 -Auxiliary Output 5 ports.(Refer to 20.3 Assigning Functions to theAuxiliary Output Ports.)AUX I/O 1 On-AUX I/O 6 OnThe function assigned to a specified AuxiliaryI/O port is enabled when TKR-750/850/751/851 starts operation.You can assign functions when “Selectable”is configured to the Auxiliary I/O 1 - AuxiliaryI/O 6 ports. (Refer to 20.3 AssigningFunctions to the Auxiliary Output Ports.)Channel 1-Channel 16Move to the channel selected from CH 1 toCH 16 immediately.You are not allowed to perform this functionwhen Channel Select is configured to theAuxiliary I/O 1 to Auxiliary I/O 4 ports. “E2”appears on the display when specifying thechannel has no data.(Refer to 20.1 AUX I/O Function.)Channel Down Decrease a channel to the next.The blank channel is skipped.Channel Up Increase a channel to the next.The blank channel is skipped.CW ID OnTransmits a CW ID when it starts operation.(Refer to 22.1 CW ID.)This function performs on a channel havingCW ID.CW Message 1-CW Message 8Transmits a assigned CW tone from CWMessages 1 to 8 when it starts operation.(Refer to 22.2 CW Message.)DC Power SaveOffExits Save Mode when it starts operation.You cannot configure this function to theSave On/Off Function.DC Power SaveOnEnters Save Mode when it starts operation.You cannot configure this function to theSave On/Off Function.Display OffAll LEDs other than the Power SW LED thatis located on the front panel are unlit.This function activates only when TKR-750/850/751/851 is in Save Mode.Display OnAll LEDs on the front panel light.This function activates only when TKR-750/850/751/851 operates in Save Mode.Hold TimeDisableDisables the Repeat Hold Time.You can configure this function only when atleast one channel is configured as RepeatOperation mode and the Repeat Hold Timeis enabled. (Refer to 6.5 Repeat Hold Time.)Hold TimeEnableEnables the Repeat Hold Time.You can configure this function only when atleast one channel is configured as RepeatOperation mode and the Repeat Hold Timeis enabled. (Refer to 6.5 Repeat Hold Time.)Local TX Disable Inhibits a transmission by Local Mic PTT.Local TX Enable Enables a transmissions by Local Mic PTT.Low Power Off*1Switches a transmission power from Low toHigh.This function activates only when at leastone channel is configured as High for TXPower. (Refer to 4.10 TX High Power.)Low Power On*1Switches a transmission power from High toLow.This function activates only when at leastone channel is configured as High for TXPower. (Refer to 4.10 TX High Power.)Monitor Off Enables a Signalling Decode function.Monitor On Disables a Signalling Decode function.Multi-table SubThe signalling specified in a Multi-tableSelect is switched to the Sub-table. (Refer to20.1 AUX I/O Function.)Multi-table MainThe signalling specified in the Multi-tableSelect is switched to the Main-table. (Referto 20.1 AUX I/O Function.)QT/DQT DecodeDisableDisables a QT/DQT Decode function. Itbecomes carrier squelch. This functionactivates even when the repeater is makingthe repeat operation.Name offunctions Description of functions