Version: 1.01 USA Function Reference (FUNC) 3215 KEY ASSIGNMENTYou can assign functions to PF1 to PF6 keys that arelocated on the front panel of the TKR-750/850/751/851/751/851.! Configuration of KPG-91D" Assigning functions to PF keys (Refer to FPRG 6.5“Key Assignment” window.)15.1 Available FunctionsYou can assign functions to PF1 to PF6 keys by KPG-91D.When the Channel Up function is assigned to the PF1key, the PF1 key is referred to as “PF [Channel Up] key”.Table 15-1 Available functionsName offunctions Description of functionsNone TKR-750/850/751/851/751/851 does notperform any operation.AUX Out 1On/Off-AUX Out 5On/OffYou can enable/disable a function assignedto an auxiliary output port by pressing one ofPF [AUX Out 1 On/Off] to PF [AUX Out 5 On/Off] keys.You can assign functions when Selectable isconfigured to an Auxiliary Output 1 toAuxiliary Output 5 port. (Refer to 20.3Assigning Functions to the Auxiliary OutputPorts.)AUX I/O 1On/Off-AUX I/O 6On/OffYou can enable/disable a function assignedto an auxiliary I/O port by pressing one of thePF [AUX Out 1 On/Off] to PF [AUX Out 6 On/Off] keys.You can assign functions when Selectable isconfigured to the Auxiliary I/O 1 to Auxiliary I/O 6 ports. (Refer to 20.3 Assigning Functionsto the Auxiliary Output Ports.)Channel 1-Channel 16Change a channel from one of CH 1 to CH16 channels directly by pressing one of thePF [Channel 1] to PF [Channel 16] keys.TKR-750/850/751/851/751/851 cannotconfigure this function when Channel Selectis configured to an Auxiliary I/O 1 to AuxiliaryI/O 4 ports. “E2” appears on the displaywhen specifying the channel has no data.(Refer to 20.1 AUX I/O Function.)Channel DownChange channel to the next lower bypressing a PF [Channel Down] key.The blank channel is skipped.Channel UpChange channel to the next higher bypressing the PF [Channel Up] key.The blank channel is skipped.CW ID OnTransmits a CW ID by pressing the PF [CWID On] key. (Refer to 22.1 CW ID.)This function is available on a channelhaving CW ID configuration.CW Message 1-CW Message 8Transmits one of CW Message 1 to CWMessage 8 by pressing one of the PF [CWMessage 1] to PF [CW Message 8] keys.(Refer to 22.2 CW Message.)DC Power SaveOn/OffEnable/disable Save Mode by pressing thePF [DC Power Save On/Off] key. (Refer to10.4 DC Power Save.)Display On/OffSwitch the panel LED On/Off by pressing thePF [Display On/Off] key.This function operates only when TKR-750/850/751/851/751/851 is in Save Mode.Hold TimeDisable/EnableDisable/enable the Repeat Hold Time bypressing a PF [Hold Time Disable/Enable]key.You are able to configure this function onlywhen at least one channel is configured asRepeat Operation mode and the RepeatHold Time is enabled. (Refer to 6.5 RepeatHold Time.)Local TXDisable/EnableDisable/enable a transmissions caused byLocal Mic PTT by pressing the PF [Local TXDisable/Enable] key. (Refer to 6 PTTOperation.)Low PowerOn/OffSwitch High or Low of a transmission powerby pressing the PF [Low Power On/Off].This function is available only when at leastone channel is configured as High Power.(Refer to 4.10 TX High Power.)Monitor On/OffDisable/enable the Signalling Decodefunction by pressing a PF [Monitor On/Off]key.MonitorMomentaryTKR-750/850/751/851 activates the Monitorfunction while pressing the PF [MonitorMomentary] key.Multi TableMain/SubYou can toggle between Main and Sub forthe signalling specified by the Multi-tableSelect by pressing the PF [Multi Table Main/Sub] key. (Refer to 20.1 AUX I/O Function.)QT/DQT DecodeDisable/EnableYou can disable/enable the QT/DQT Decodefunction by pressing the PF [QT/DQTDecode Disable/Enable] key.QT/DQT EncodeDisable/EnableYou can disable/enable the QT/DQT Encodefunction by pressing the PF [QT/DQTEncode Disable/Enable] key.Repeat Disable/EnableYou can disable/enable a repeat operation bypressing the PF [Repeat Disable/Enable]key.You are not allowed to assign this functionwhen no channel is configured as RepeatOperation mode.ResetThe operation of the TKR-750/850/751/851is reseted and it returns to the default valueby pressing the PF [Reset] key.Scan On/Off Enable/disable the Scan function by pressingthe PF [Scan On/Off] key.Name offunctions Description of functions