15Chapter One : Connecting Your DevicesConnectionsConnecting Your Primary CD Player, continuedDo not plug in the receiver to AC power until you haveconnected all your devices.This section focuses on the connections from your 200-DiscCD Changer to the VR-4900/VR-4700/KRF-V9993D. Pleaserefer to your changer’s instructions for more detail aboutits connection jacks and capabilities.Each set of instructions in this section shows one of severalpossible variations on connecting your CD player(s). Forfurther assistance on optional configurations, contact thestore where you purchased your CD player(s).The illustration shows a Kenwood 200-Disc CD Changer.Your CD player may look different.The Kenwood CD-3280M, CD-2280M and DPF-J9030 /DPF-J9010 200-Disc Changers contain two CD transports.You must connect these devices as though they were twoCD players. (CD-2280M and CD-3280M are sold only inUSA and Canada.)What if I Have a Video CD-Compatible CDPlayer?Connect the audio and video cables from the CD player toany unused Video jack set.Do not connect the system control cable in this instance.To Connect a Kenwood 200-Disc CDChanger:1. Connect one set of audio cables from the 200-DiscChanger to the receiver’s CD1 jacks. If you have aCD-3280M, CD-2280M, DPF-J9010 or DPF-J9030,connect Output A to the receiver’s CD1 jacks and OutputB to the receiver’s CD2/TAPE2 MONITOR PLAY IN jacksas shown to the left.2. Connect the digital cable from the changer to thereceiver’s CD1 digital jack as shown to the left.3. Connect the system control cable from the changer tothe SYSTEM CONTROL jack as shown to the left.Be sure that the SL16/XS8 switch on the changer is setto SL16.If you are connecting more than one Kenwood devicewith a system control cable, see “What if I Have SeveralKenwood Devices (System Control Chaining)?” onpage␣ 30 for more information.4. Connect the SL16 text cable (communication cable)from the changer to the receiver’s SL16 TEXT jack asshown to the left.5. Go to “Noting Your Devices” on page␣ 3 and note whichjacks you used to connect your CD changer. In addi-tion, note the brand name and model number of theCD Changer.See “What if I Connected a CD Player to the Jack SetPowerTouch Calls Tape2?” on page 38 to configure the CD2/TAPE2 as a CD2 input for the CD-2280M, CD-3280M, DPF-J9010 or DPF-J9030.To Connect Any Other Primary CD Player orChanger:1. Connect the audio cables from the CD player’s audiojacks to the receiver’s CD1 jack set as shown to the left.2. Connect the digital cable from the CD player’s digitaljack to the receiver’s CD1 digital jack as shown to theleft.3. If you are connecting a Kenwood CD Player with sys-tem control, connect the system control cable from theCD player to the system control jack as shown to theleft.Be sure that the SL16/XS8 switch on the player/changeris set to SL16.If you are connecting more than one Kenwood devicewith a system control cable, see “What if I Have SeveralKenwood Devices (System Control Chaining)?” onpage␣ 30 for more information.4. Go to “Noting Your Devices” on page␣ 3 and note whichjacks you used to connect your CD player/changer. Inaddition, note the brand name and model number ofthe CD player or changer.To Connect a Secondary CD Player:See “Connecting Your Secondary CD Player or Tape Deck”on page␣ 22.Do not connect the system control cable in this instance.When playing a HDCD disc in the HDCD format (highquality mode), use the digital connection jacks.