La Marche TPSD Installation And Operation Manual
Also see for TPSD: Instructions
                                              | |
Contents
| 
314.3.5 Ground and Short Circuit Test.A simple ohmmeter check can be performed to check the unit for a short to ground, primary to secondarybreakdown, AC-DC short, or DC ground. Before installation of a new unit, the above checks should be madebefore installing. If a short of this type is suspected on a unit in service, check as follows:1. Disconnect AC input power to the unit. Disconnect the DC battery and loads from the rectifier.2. Set ohmmeter scale on ohms scale RX100.3. Measure from one terminal of the input to one terminal of the output. Meter should not indicate. If themeter reads full scale deflection, this indicates an ac-dc short. During shipping, an AC wire may rub againstthe DC lugs, terminals, etc. And cause a short. These problems may be eliminated by being very careful ininspecting the wiring to make certain the AC wires are not touching the DC wiring.4. Check the input terminals to ground and check the output terminals ground. If the meter indicates fullscale deflection, a wire is touching a metal part of the rectifier. Look for wires that are near any metal partand inspect for possible breakdown caused by shipping. The heatsink of the diodes and the control unit areinsulated from ground through the mounting legs.4.3.6 Troubleshooting the TRIACThe procedure for checking the triac is as follows:1. On the ohmmeter, set the switches on “ohms”, “DC”, and “Rx10,000” scale.2. Disconnect the triac to be checked. Using an ohmmeter, measure the resistance between main terminals,MT1 and MT2 in both directions. A good device will indicate open circuit in both directions, a low resistanceindicates a shorted device.3. Set ohmmeter to Rx100 scale.4. To check for a shorted triac gate lead, measure the resistance between gate (GATE) lead and main terminalMT1. A reading of zero ohms in both directions indicates a shorted gate. A reading of infinity in bothdirections indicates an open gate and the triac should be replaced. A good device should have resistance inboth directions, but not zero ohms.4.3.7 Troubleshooting and Replacing Power Silicon Diodes/Modules1. On the ohmmeter, set the switches on “ohms”, “DC”, and “Rx100” scale.2. Isolate one end of the diode by disconnecting the wires attached to the nipple (or pigtail) end of the diode(only one end of the diode must be disconnected). On a diode module, both of the outside leads must bedisconnected.3. Clip one lead of the ohmmeter to the anode lead of the diode. Clip the other ohmmeter lead to the cathode.4. Note the ohmmeter reading. Then reverse the leads to the diode. Again, note the ohmmeter reading. Ifthe diode is good, the meter will indicate a high resistance in one direction and a low resistance with theleads reversed. If the diode is shorted, the meter will read full scale, or zero (“O”) resistance with theleads in either direction. If the diode is “open”, the ohmmeter needle will not indicate or it will show infiniteresistance in either direction, indicating an open circuit.5. All diodes must be checked in the event that more than one diode is defective.6. If the diode is defective, remove the defective diode from the heatsink and replace with a new diode.4.3.8 Checking Capacitors1. When checking capacitors be sure all AC power is turned off and battery is disconnected from unit. Checkcapacitors with DC voltmeter to see that DC voltage is at near -0- volts.2. Momentarily short circuit the capacitor leads to assure complete discharge.3. Connect the meter test leads to the capacitor leads or terminals and observe indicated resistance.4. A good capacitor will indicate an initial low resistance and gradually increase as the capacitor charges. Thefinal resistance of a good capacitor is usually several hundred thousand ohms approaching a megohm.5. Initial high resistance approaching infinity indicates an open capacitor. Initial and continued low resistancereadings indicate a shorted capacitor.When ordering replacement parts, drawings, or schematics, always give model number, serialnumber and AC input voltage. |
Related manuals for La Marche TPSD
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine