NAD VISO FIVE Owner's Manual

Also see for VISO FIVE: Catalog Brochure Datasheet Owner's manual Service manual

NAD VISO FIVE Owner's Manual Manual pdf 18 page image

VIDEO SETUP MENUDISC VIDEOFORMATSet FORMAT to select a picture size matching the aspect ratio of yourTV/Monitor.Select “Pan Scan 4:3” or “Letter Box 4:3” when a standard 4:3 TV is connected.Letter Box 4:3 : Displays a wide picture with bands on the upper andlower portions of the screen.Pan Scan 4:3 : Automatically displays the wide picture on the entirescreen and cuts off the portions that do not fit.Widescreen 16:9 : Select when a 16:9 wide TV is connected. Set thewidescreen TV to FULL mode if necessary.NOTEIf you have a 16:9 display device and you have defaulted “Format” to“Widescreen 16:9”, it does not mean you will always see movies in thisformat - Widescreen 16:9 display format must be supported by the discbeing played in order to view the movie in widescreen format.SIGNAL MODEDepending on the type of TV/Monitor set you own, select the signal modeyou wish to watch your disc. Refer to your TV/Monitor’s owner’s manual tocheck its signal or system mode capabilities.Auto : Automatically detects the signal mode of your TV/Monitor.NTSC : Select when the signal mode of your TV/Monitor is NTSC system.PAL : Select when the signal mode of your TV/Monitor is PAL system.HDMI RES (RESOLUTION)HDMI video resolution can be adjusted with the VISO FIVE connected to anHDMI-compatible component via HDMI OUT.480P/576P, 720P, 1080I : Set applicable resolution depending on yourTV/Monitor capability.Auto : The best resolution is automatically selected based on yourTV/monitor’s capability.Off : Select to turn off HDMI output.NOTES• For settings other than “Auto”, be sure that the selected resolutionis supported by the HDMI-compatible monitor you are using. If theselected resolution is not supported, this setting is automaticallyswitched to the most appropriate resolution.• Picture quality may decrease when an HDMI cable longer than 5m is used.IMPORTANT NOTE ABOUT HDMI CONNECTION AND SETTINGWith HDMI OUT connected to a HDMI-compatible component, componentvideo out, composite and S-video output will only be available when “HDMIRes.” is set to “480P/576P” or “Off”. For component video out, composite andS-video to come up, unplug HDMI cable or undertake the following:1 At DVD mode and with no disc loaded, “NO DISC”, press and hold[DISPLAY] button. The lower line of the VFD will show the current HDMIresolution setting.2 Use the remote’s [ ] keys or toggle [MEMORY] button to selectthrough 480P/576P, 720P, 1080I, AUTO or OFF. Select either “480P/576P”or “OFF” to enable component video out, composite and S-Videooutput. To set preferred resolution setting, stop at your desiredresolution setting and release [ ] keys or [MEMORY] button.BRIGHTNESSAdjust overall brightness of the image. Set the brightness level over arange ±7. Select “BASIC” to maintain default brightness setting.SHARPNESSPicture sharpness could be easily lost during the recording/playbackprocess. Adjust sharpness to improve the fine details of the picture. Setthe sharpness level over a range ±7. Select “BASIC” to maintain defaultsharpness setting.VIDEO OUTPUT (EUROPE VERSION MODEL ONLY)Select between “Component” and “RGB” as your preferred video outputmedia. Make sure the appropriate video out of VISO FIVE is connected tothe corresponding video input of your TV/monitor.“RGB” video setting is preferable if your output media is through SCARTOUT. At RGB setting, video signal is split into three fundamental colors Red,Green and Blue (RGB) resulting to greater picture resolution and eliminationof artifacts associated with traditional composite video signals.Select “Component” if you are not using SCART OUT as your output media.OPERATIONUSING THE VISO FIVE – VIDEO SETUP MENU18ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ