IV Safety considerations4 Sweep Mode operating instructions4.1 Introduction………………………………………………………………………4.2 Measure………………………………………………………………………….4.2.1 Frequency……………………………………………………………………...4.2.2 Level………………….………………………………………………………...4.2.2.1 Input: Attenuator and Preamplifier….…………………………………….4.2.2.2 Misc…………………………………………………………….…………….4.2.2.2.1 Tracking generator……………………………………………………….4.2.2.3 Detector……………………………………………………………………...4.2.2.4 Smart detector…………………………………………………..................4.2.3 Conversion factor……………………………………………………………..4.3 Limit………………………………………………………………………………4.4 Display……………………………………………………………………………4.5 Marker…………………………………………………………………………….4.6 Load & Store.…………………………………………………………………….4.7 Ultra fast FFT scan……………………………………………………………...Page4-14-24-24-34-34-44-44-54-54-64-64-64-74-84-85 Analyzer Mode operating instructions5.1 Introduction………………………………………………………………………5.2 Frequency………………………………………………………………………..5.3 RBW………………………………………………………………………………5.4 Level………………………………………………………………………………5.4.1 Input Attenuators and Preamplifier……..…………………………………..5.4.2 OVER RANGE Message…………………………………………………….5.4.3 Misc…………………..…………………………………………………………5.4.3.1 Tracking generator…………………………………………………………5.4.4 Detector………..……………………………………………………………….5.4.5 Conversion factor……………………………………………………………..5.5 Marker……..….………………………………………………………………….5.6 Esc………………………………………………………………………………..Page5-15-25-35-35-35-45-45-55-55-65-65-66 Manual Mode operating instructions6.1 Introduction………………………………………………………………………6.2 Frequency………………………………………………………………………..6.3 Level………………………………………………………………………………6.3.1 Input: Attenuator and preamplifier………………………………………….6.3.2 Misc…………………………………………………………………………….6.4 RBW………………………………………………………………………………6.5 Hold Time………………………………………………………………………...6.6 Demodulator……………………………………………………………………..Page6-16-26-26-36-36-56-56-57. Applications7.1 Measuring the EMI Voltage……………………………………………………...7.1.1 Measuring Principle with a LISN………………………………………….....7.1.2 Coupling Networks……………………………………………………………7.1.2.1 AMN…………………………………………………………………………..7.1.2.2 Current probe……………………………………………………………….7.1.2.3 Voltage probe……………………………………………………………….7.1.3 Test setup……………………………………………………………………..7.1.4 Guidance on a preliminary Measuring Procedure………………………..7.1.5 Remarks and hints for Measuring…………………………………………..Page7-17-17-17-27-37-37-47-47-58. Updating firmware and Activation code Utility8.1 Introduction………………………………………………………………………8.2 System requirements ……………………………….………………………….8.3 Preparing the Hardware…………………………….………………………….8.4 Software installation…………………………………………………................8.5 To transfer data……………….……………………………………..………….8.6 9010 Set code utility ...……….……………………………………..………….Page8-18-18-18-18-38-5
