Panasonic AW-RP605 Operating Instructions Manual

Also see for AWPS505 - AC ADAPTOR: Operating instructions Operating instructions Operating instructions

Contents

22Operation$ Video signal cable compensationSignal deterioration caused by the length of the cables fromthe pan-tilt head to the main unit is compensated for.When the length of the cables from the pan-tilt head to themain unit exceeds 500 meters, set the cable compensationswitch inside the pan-tilt head to ON.For further details, refer to the operating instructions of thepan-tilt head.1. Select the pan-tilt head system using theCONTROL/PREVIEW MONITOR OUT SEL button.2. Press the MENU button, turn the menu setting control(main), and set it so that the CABLE COMP itemappears at the top of the LCD panel.3. Press the OK button.The following item appears on the LCD panel.4. Press the OK button.The adjustment of the cable compensation for thecurrently selected pan-tilt head system commences, andthe OK button’s lamp flashes.If composite signals have been set as the video inputsignals, the output signals from the convertible cameraare switched to color bar signals, and automaticadjustment is performed.Alternatively, if component signals have been set as thevideo input signals, the output signals from theconvertible camera are switched to color bar signals ofY/C signals, and automatic adjustment is performed.5. Upon completion of the adjustment, the OK button’slamp goes off. The following item appears on the LCDpanel.6. Select the next pan-tilt head system using theCONTROL/PREVIEW MONITOR OUT SEL button, andcontinue adjusting the cable compensation for eachsystem concerned.A small error may arise in the automatic adjustment. Ifprecise adjustment is required, perform the adjustmentmanually. (Refer to the following page.)CCAABBLLEE CCOOMMPP AAUUTTOOAADDJJUUSSTT OOKKCCAABBLLEE CCOOMMPP AAUUTTOOAAUUTTOO AADDJJUUSSTTCCAABBLLEE CCOOMMPP AAUUTTOOSSTTAARRTT?? n OOKK KKeeyyCCAABBLLEE CCOOMMPPn OOKK KKeeyyAutomatically adjusting the cable compensationCONTROL/PREVIEW MONITOR OUT SELAUX1 2 3 4 5TALLYTRACING MEMORYLAMPMENULIMITOFFLIMITONFULLEMPTYOKLCDCONTRASTCAMERACONTROLSTARTPOINTR/BGAIN/PEDWHITEBAL AWCGAINMODECLOSE WIDE NEARDATA SETTR/PSET M.LOCKMEMORYIRISIRISIRISOPEN ZOOMTELE FOCUSFARCALLINCOMLEVELFOCUSOPENFARTELEOFFONOPERATEWIDEZOOM/FOCUS/IRISABCATWAB NGOKSTART/STOP RESTORE RESETDEF WIP H/F EXT ND OPTIONPAN/TILT SETCAMERA CONTROLTRACING/PRESET MEMORYIRISSPEEDPRIORITYFOCUSBARCAMTRPSETLOWHIGHAUTOMANUAUTOMANULOCK1 2 3 4 5 6 7 8 9 1011 12 13 14 15 16 17 18 19 2021 22 23 24 25 26 27 28 29 13031 32 33 34 35 36 37 38 39 4041 42 43 44 45 46 47 48 49 50DOWNPAN/TILT/FOCUS/IRISUPL RCLOSENEAR OPENFARCLOSENEAR22 3•4 1If the automatic adjustment was not performed properly,the following item appears on the LCD panel.Check the connection of the output signals from theconvertible camera and cables, and proceed with theautomatic adjustment again.If the automatic adjustment was not performed properlyagain even by following the automatic adjustmentprocedure, perform the adjustment manually instead.Consult your dealer if the adjustment still cannot beperformed properly even when the manual procedure isfollowed.CCAABBLLEE CCOOMMPP AAUUTTOOAADDJJUUSSTT NNGG