Panasonic AW-RP605 Operating Instructions Manual

Also see for AWPS505 - AC ADAPTOR: Operating instructions Operating instructions Operating instructions

Contents

38Setting menusCABLE LENGTH (SHORT, LONG)This item sets the compensation for the length of the BNCcable used for the genlock signals. “SHORT” is set whenthe cable is less than 500 meters long; “LONG” is set whenit is 500 meters or longer.H PHASE (–206 to +49)This item is used to adjust the horizontal phase duringgenlock.SC PHASE (1, 2, 3, 4, –511 to +511)This item is used to adjust the color phase during genlock.CABLE COMP AUTOWhen this item is selected and the OK button is pressed,the cable compensation is adjusted automatically.Perform these operations to achieve a simple adjustment orwhen a waveform monitor, vectorscope or other suchmeasuring instrument is not available.CABLE COMP MANUAL (Y: 0 to 255; C: 0 to 255)Select this item to adjust the cable compensation manuallywhen C.VIDEO has been selected as the input signal settingfor the SIGNAL SELECT item on the CONTROLLERSETTING menu.CABLE COMP MANUAL Y LEVEL (0 to 255)Select this item to adjust the cable compensation manuallywhen Y/Pr/Pb has been selected as the input signal settingfor the SIGNAL SELECT item on the CONTROLLERSETTING menu.When it is selected, the multi-function controller’s videooutput signals are automatically set to Y/Pr/Pb. When it isreleased, the original video output signals are restored.CABLE COMP MANUAL f Response (0 to 255)Select this item to adjust the compensation for thefrequency response manually when Y/Pr/Pb has beenselected as the input signal setting for the SIGNAL SELECTitem on the CONTROLLER SETTING menu.When it is selected, the output signals from the camera areautomatically set to Y/C, and the multi-function controller’svideo output signals are set to Y/Pr/Pb. The frequencyresponse is compensated by adjusting the burst level usingthe Pr output signal. When this item is released, the originalvideo output signals are restored.CABLE COMP (cable compensation)menuG/L SETTING (genlock adjustment)menuSIGNAL SELECT(C.VIDEO5C.VIDEO, Y/Pr/Pb5C.VIDEO, Y/Pr/Pb5Y/Pr/Pb)This is used to set the multi-function controller’s inputsignals and output signals.When the signals supplied to the multi-function controllerhave been set to C.VIDEO (composite signals), the outputsignals signals are fixed to the C.VIDEO as well.When the signals supplied to the multi-function controllerhave been set to Y/Pr/Pb (component signals), either theY/Pr/Pb or C.VIDEO signals can be selected as the outputsignals.BUZZER SET (ON/OFF)This is used to set the buzzer contained inside the controlpanel to ON or OFF. The buzzer does not sound when OFFis selected as this item’s setting.At the ON setting, the buzzer sounds when the CALL buttonis pressed and when a tracing memory operation (entry,recall or change) has been started, suspended or data entryhas been completed.EXT CONTROL OUT (ON/OFF)When ON is selected as this item’s setting, the pan-tilt headsystem’s control signals are output from the EXTERNALCONTROL OUT connector used for additional functions.Since it is not supported at the present time, select the OFFsetting for use.COMPONENT (RGB, Y/Pr/Pb, Y/C)This item is used to select the video signals which are to beoutput when the RGB card (AW-PB302) has been installedin the OPTION CARD slot.MEMORY LENGTH (30s, 60s, 150s, 300s)This item is used to set the tracing memory entry time(memory length) and number of memories.30s : 30 seconds a 10 memories60s : 60 seconds a 5 memories150s : 150 seconds a 2 memories300s : 300 seconds a 1 memoryIf data has already been entered into a tracing memory, theentry time and number of memories cannot be set. Beforeentering different settings, delete the contents of the tracingmemory.HEAD SW (R) FUNCTION (ON/OFF)When ON is selected as this item’s setting, it is no longerpossible to switch the adjustment dial functions (IRIS andFOCUS) using the button on the top surface of thePAN/TILT lever.Since it is not supported at the present time, select the OFFsetting for use.VIRTUAL STUDIO MODE (ON/OFF)When ON is selected as this item’s setting, the camera’svideo signals are switched to the corrected color position forusing the blue background of the virtual studio.CONTROLLER SETTING (controllersetting) menu