Panasonic PT PT-DW5100EL Operating Instructions Manual

Also see for PT-D5700E: Information sheet Service manual Service manual

Contents

Panasonic PT PT-DW5100EL Operating Instructions Manual Manual pdf 29 page image

29 ENGLISHAdjusting the positionPOSITIONSHIFTASPECTZOOMCLOCK PHASEKEYSTONEMENU SELECT4:3+16SUB MENUSHIFTThe position where the images are displayed can be moved here.: The position is moved horizontally.: The position is moved vertically.ASPECTAUTO : (For S-Video/Video signals only)At this setting, when S1 video signals* 1 areidentified as being input to the S-Videoconnector or video ID signals are identifiedas being input to the video connector, theimages are displayed after automaticallybeing converted to the 16:9 aspect ratio.16:9 : At this setting, when standard signals*2 areinput, the images are converted to the 16:9aspect ratio and displayed. When wide-screensignals*3 are input, the images are displayedwith their inherent aspect ratio intact.4:3 : At this setting, when standard signals*2 are input,the images are displayed with their inherent aspectratio intact. When wide-screen signals*3 are input,they are converted by the PT-D5700E/PT-D5700EL to the 4:3 aspect ratio and displayed.With the PT-DW5100E/PT-DW5100EL, the imagesare reduced in size and displayed withoutconverting their aspect ratio so that they will fit ontoa screen with a 4:3 aspect ratio.S4:3 : Select this setting when using a 16:9 screen.H FIT : Pictures are displayed using all the panelpixels in the horizontal direction. When asignal has an aspect ratio taller than that ofthe panel pixel* 4, the image will be displayedwith the top and bottom portions cut off.V FIT : Pictures are displayed using all the panelpixels in the vertical direction. When a signalhas an aspect ratio wider than that of thepanel pixel*4, the image will be displayed withthe left and right sides cut off.HV FIT : The image is displayed on all the panelpixels* 4. When the aspect ratio of the inputsignal is different from that of the panelpixel*4, the signal is transformed to the aspectratio of the panel pixel*4 and then displayed.*1 S1 video signals are 16:9 video signals to which is added the detection signaloutput from the video deck or other unit which supports the wide-screen format.*2 Here, the standard signal means 4:3 or 5:4 input signals.*3 Here, the wide-screen signals means 16:9, 15:9 or 15:10 input signals*4 Panel pixel aspect ratio is 4:3 in the case of PT-D5700E/PT-D5700ELand 15:9 for PT-DW5100E/PT-DW5100EL.• If you choose an aspect ratio that does notmatch the source video’s aspect ratio, youwill see a picture with an aspect ratio not thesame as that of the original picture. Choosethe appropriate aspect ratio carefully tomatch that of the original picture.AttentionSHARPNESS“SHARPNESS” is used to adjust the crispness ofthe image.: Sharpens the edge of the image.: Softens the edge of the image.NOISE REDUCTIONIn this mode, the video noise is reduced.OFF : No correction1 : Low2 : Middle3 : HighAIGray scale control is exercised to suit the images,and optimal images with a clear contrast areprojected.ON : AI compensation is enabled.OFF : AI compensation is disabled.SYSTEM SELECTORSet this according to the connected signal system.(S-Video/Video terminal input signal)AUTO : This is the standard setting. Thereceived signal system is automaticallyidentified.(RGB1/RGB2 terminal input signals)AUTO : This is the standard setting. Thereceived signal system is automaticallyidentified.When VGA60/480p signals are inputWhen other than VGA60/480p are inputFor the signals which are supported, refer to page61.AUTOYCB CRVGA60480pRGBAUTOYPB PR (YCB CR )RGBAUTOPAL60NTSCSECAMNTSC4.43PAL-NPALPAL-M• When signal deterioration or otherfactors prevent images from beingdisplayed correctly with the “AUTO”setting, change the setting to matchthe connected signal system.Note(Continued on the next page)