Panasonic PT PT-DW5100EL Operating Instructions Manual

Also see for PT-D5700E: Information sheet Service manual Service manual

Contents

Panasonic PT PT-DW5100EL Operating Instructions Manual Manual pdf 47 page image

47 ENGLISHContents of mail sent• Mail with the contents shown below is sent when the E-mailsettings have been established.Adjust clock pageClick [Network set up], then [Adjust clock] to display the Adjust clock page.• Mail with the contents shown below is sentwhen an error has occurred.• If the time becomes incorrect immediately after setting the correct time, then the battery needs tobe changed. Contact the dealer where you bought the projector to have the battery changed.Note=== Panasonic projector report(CONFIGURE) ===Projector Type : D5700----- E-mail setup data -----TEMPERATURE WARNING SETUPMINIMUM TIME at [ 60] minutes intervalINPUT AIR TEMPERATURE Over [ 45C / 113F ]ERROR [ ON ]LAMP1 RUNTIME [ ON ] at REMAIN [ 100] HLAMP1 RUNTIME [ ON ] at REMAIN [ 200] HLAMP2 RUNTIME [ ON ] at REMAIN [ 300] HLAMP2 RUNTIME [ ON ] at REMAIN [ 400] HINPUT AIR TEMPERATURE [ OFF ]PERIODIC REPORTSunday [ ON ] Monday [ OFF ] Tuesday [ ON ] Wednesday [ OFF ]Thursday [ ON ] Friday [ OFF ] Saturday [ ON ]00:00 [ ON ] 01:00 [ OFF ] 02:00 [ ON ] 03:00 [ OFF ]04:00 [ OFF ] 05:00 [ ON ] 06:00 [ OFF ] 07:00 [ ON ]08:00 [ ON ] 09:00 [ OFF ] 10:00 [ ON ] 11:00 [ OFF ]12:00 [ OFF ] 13:00 [ ON ] 14:00 [ OFF ] 15:00 [ ON ]16:00 [ ON ] 17:00 [ OFF ] 18:00 [ ON ] 19:00 [ OFF ]20:00 [ OFF ] 21:00 [ ON ] 22:00 [ OFF ] 23:00 [ ON ]----- check system -----MAIN CPU BUS [ OK ]FAN [ OK ]OPTICS MODULE TEMPERATURE [ OK ]INPUT AIR TEMPERATURE [ OK ]AROUND LAMP TEMPERATURE [ OK ]LAMP2 REMAIN TIME [ OK ]LAMP1 REMAIN TIME [ OK ]•••=== Panasonic projector report(ERROR) ===Projector Type : D5700––––– check system –––––MAIN CPU BUS [ OK ]FAN [ OK ]OPTICS MODULE TEMPERATURE [ OK ]INPUT AIR TEMPERATURE [ OK ]AROUND LAMP TEMPERATURE [ OK ]LAMP2 REMAIN TIME [ OK ]LAMP1 REMAIN TIME [ OK ]LAMP2 STATUS [ OK ]LAMP1 STATUS [ OK ]SHUTTER [ FAILED ]AIR FILTER [ OK ]OPTICS MODULE TEMP.SENSOR [ OK ]INPUT AIR TEMP.SENSOR [ OK ]AROUND LAMP TEMP.SENSOR [ OK ]BATTERY [ OK ]AIRFLOW SENSOR [ OK ]COLOR WHEEL [ OK ]COVER OPEN [ OK ](Error code 00 10 00 00 00 00 00 00)Input air temperature : 30 degC / 86 degFOptics module temperature : 30 degC / 86 degFAround lamp temperature : 37 degC / 98 degFSET RUNTIME 30 HPOWER ON 33 timesLAMP1 ON 34 timesLAMP1 LOW 25 HLAMP1 HIGH 5 HLAMP2 ON 24 timesLAMP2 LOW 16 HLAMP2 HIGH 4 HLAMP1 REMAIN 1476 HLAMP2 REMAIN 1484 H----- Network configuration -----IP address 192.168.0.8MAC address 00:00:00:00:00:00Thu Mar 02 14:11:02 2006----- Memo -----Time zone selectionButton to update time zone settingButton to update time and datesettingsNew date fieldNew time field