Panasonic WJ-SX150 Operating Instructions Manual

Also see for WJSX150 - SWITCHER - ADDENDUM: Addendum Addendum manual Operating instructions

Contents

Panasonic WJ-SX150 Operating Instructions Manual Manual pdf 48 page image

50GENLOCKON: Select this mode when you gen-lock the unitthrough an external device (such as a recorder).Images via the EXT IN connector are not displayedon Monitor 1 to 4.OFF: Select this mode when you don't gen-lock the unitthrough an external device. Images via the EXT INconnector can be displayed on Monitor 1 to 4.The factory default setting is GENLOCK OFF.Notes:• If GENLOCK ON is selected, the playback images ormultiscreen display cannot be displayed on Monitor 1to 4. Confirm the images on the monitor which are con-nected to the recorder.• If GENLOCK OFF is selected, the maximum raterecording becomes unavailable (when WJ-HD500A isconnected to the unit).• CAMERA CLEANINGON: Activates the manual cleaning for the cameras.OFF: Deactivates the manual cleaning.When you set CAMERA CLEANING to ON and exit from theSETUP MENU, camera cleaning will start.The factory default setting is OFF.Notes:• When the camera cleaning is active, cleaning will beginfrom CAM 1 in numerical order.• Surveillance is impossible during the cleaning.• The cleaning cannot be stopped after it is started.• Refer to pp. 34 and 36 for details on RS-485 or PS·Dataconnections.• The camera address needs to be corresponding withthe camera number.■ OPERATOR REGISTRATION● How to DisplayTo display this menu on the monitor, move the cursor to700 OPERATOR REGISTRATION in SETUP MENU by mov-ing the joystick to ▼.Then, press the CAM (SET) button. Thesubmenu appears on the monitor.● ParametersMove the joystick to move the cursor.Press the NEXT or PREV button to select the desired para-meters.Press the numeric button(s) to enter a number.• OPERATOR NO.This stands for an operator number. When you enter thenumber by pressing the NEXT, PREV or numeric button(s),this menu will display the associated operator's information.1 to 16 is available.• IDThis stands for an operator ID. 1 to 99999 is available.• PASSWORDThis stands for an operator's password. 1 to 99999 is avail-able. The password will be displayed as "*" on the monitor.• PRIORITYThis stands for an operator's priority. 1 to 16 is available.(Refer to p. 15 for details on Priority Lock.)• LEVELThis stands for an operator's restrict level. It is configurablethrough Level Table (refer to p. 60 ) of SX150 AdminConsole what kind of restriction is given to the operator. 1to 3 is available.• CAM 01 to 16:These stand for an operator's camera operation coverage.The following are the parameters.VIEW & CONTROL: The operator can display thecamera image on the monitor and control pan-ning/tilting.VIEW ONLY: The operator can display the cameraimage on the monitor, but cannot control thepanning/tilting.PROHIBITED: The operator can neither display thecamera image on the monitor nor control thepanning/tilting.The following is the factory default setting of this menu.Note: When you enter an invalid number, the parameter willreturn to the state before your numerical entry.700 OPERATOR REGISTRATIONOPERATOR NO.= 1 ID =150PASSWORD=*****PRIORITY=1LEVEL =1CAM01=VIEW&CONTROL CAM09=VIEW&CONTROLCAM02=VIEW&CONTROL CAM10=VIEW&CONTROLCAM03=VIEW&CONTROL CAM11=VIEW&CONTROLCAM04=VIEW&CONTROL CAM12=VIEW&CONTROLCAM05=VIEW&CONTROL CAM13=VIEW&CONTROLCAM06=VIEW&CONTROL CAM14=VIEW&CONTROLCAM07=VIEW&CONTROL CAM15=VIEW&CONTROLCAM08=VIEW&CONTROL CAM16=VIEW&CONTROL6OPERATOR NO. ID PASSWORD LEVEL PRIORITY1 150 150 1 12 1 12345 1 23 100 100 1 34 101 101 1 45 102 102 2 56 103 103 3CAM 1 to 16 = VIEW & CONTROL (for OPERATOR NO. 1 to6