2-94. Adjustment Procedure8 The Location of Test Points and Adjusting Controls referto Wiring Diagram on page 3-1 or 3-2.4.1. Camera Adjustment4.1.1. Starting E.V.R. Adjustment Program8 Insert new floppy disk containing DOS Operating Systemand the E.V.R. Adjustment Program into the computer(IBM PC/AT) and turn on the Power Switch of the com-puter.8 When starting an adjustment, at the prompt, typeRADJ2 CW97C and press the ENTER key, an initialmenu page as shown in Fig. 4-1-1 will be displayed.4.1.2. Saving the Adjustment DataThis saving procedure is recommended to keep the currentadjustment status of the camera.8 Press the SAVE (F5) key of the computer, and the com-puter will ask you for the file name.8 Type xxxxxxxx.EV2 B40 19FF. Give an appropriate filename for xxxxxxxx within 8 letters, but do not useCW97C.8 Press the ENTER key.4.1.3. Loading the Adjustment DataThis loading procedure is recommended to return the adjust-ment status of the camera to the factory default setting orthe setting you saved before.8 Press the LOAD (F1) key of the computer, and the com-puter will ask you for the file name.8 Type CW97C.EV2 or xxxxxxxx.EV2 (xxxxxxxx means afile name you named before) and press the ENTER key.Fig 4-1-1PANASONIC REMOTE EVR ADJUSTMENT SYSTEM CCTV PRODUCT: CW970 EEPROM:0 MENU Page (1/1) PAL1. SC FREQUENCY 11.4. 3200K B_PHASE2. SC FREQUENCY 12.1. 5100K R_GAIN3.1. LL PHASE1 FOR ACtype (50Hz) 12.2. 5100K B_GAIN3.2. LL PHASE2 FOR ACtype (50Hz) 12.3. 5100K R_PHASE4. HI CLIP LEVEL 12.4. 5100K B_PHASE5. PEDESTAL 13. HIGH LIGHT CHROMA CLIP6. ALC DC7.1. VIDEO OUT GAIN (L)7.2. VIDEO OUT GAIN (H)8.1. BURST LEVEL R8.2. BURST LEVEL B8.3. BURST PHASE R8.4. BURST PHASE B9.1. WB 3200K MANU OFFSET R9.2. WB 3200K MANU OFFSET B10.1. WB 6500K ATW LIMIT R10.2. WB 6500K ATW LIMIT B11.1. 3200K R_GAIN11.2. 3200K B_GAIN11.3. 3200K R_PHASE TD4 17.73447MHz+ – 40Hz PLEASE CHOOSE MENU DATA BY ARROW-KEYLOAD (F1) QUIT (F3) SAVE (F5)3.5. EEPROM ReplacementProcedureAfter replacing EEPROM (IC5 on the Main Board) with newpart, load the initial data to EEPROM according to the fol-lowing procedure.q Turn the power off of the WV-CW970/WV-CW974.w Short between TD777 on the Servo Board or TD17 onthe Main Board (refer to Wiring Diagram on page 3-1 or3-2) and ground.e Turn the power on the WV-CW970/WV-CW974.r Make connection according to "3.1. Connection".t Insert new floppy disk containing DOS operating Systemand the E.V.R. Adjustment Program into the computer(IBM PC/AT) and turn on the Power Switch of the com-puter.y At the prompt, type RADJ2 CW97C and press theENTER key, then the initial menu page will be displayed.u Press the LOAD (F1) key of the computer, and the com-puter will ask you for the file name .i Type CW97C.EV2 and press the ENTER key.o When finishing the loading, press the QUIT (F3) key.!0 Press the N key then press the ENTER key.!1 Type RADJ2 and press the ENTER key.!2 Type W_E_0 and press the ENTER key. (refer to Fig. 3-5-1)!3 Type A5 and press the ENTER key. (refer to Fig. 3-5-1)!4 Type W_E_01 and press the ENTER key. (refer to Fig. 3-5-1)!5 Type 5A and press the ENTER key. (refer to Fig. 3-5-1)!6 Turn the power off once and on again of the WV-CW970/WV-CW974.!7 Remove the short wire from TD777 on the Servo Boardor TD17 on the Main Board.!8 Reset the Preset data according to "4.4. Preset DataReset Procedure".!9 Adjust the Camera according to "4.1. CameraAdjustment", "4.2. Back Focus Adjustment" and "4.3.Tilt Adjustment" if necessary.< EVR2 > W_E_0 N !2EEPROM000 : XX - A5 N !3< EVR2 > W_E_01 N !4EEPROM000 : XX - 5A N !5Fig. 3-5-1