Panasonic WV-CW970 Service Manual

Also see for Super Dynamic III WV-CW974: Product catalog Product catalog Brochure & specs Specifications Operating instructions

Contents

2-12(8.4) Burst Phase B AdjustmentTest Point: Video Output Connector8 Keep the Colour Temperature at 3 200°K.8 Set the Mode Switch of the Vectorscope to NTSC mode.8 Adjust data with the ARROW Keys so that the Burstphase becomes 135° ± 1° as shown in Fig. 4-1-10.8 Change the Mode Switch of the Vectorscope from theNTSC mode to the PAL mode.8 Adjust data with the ARROW Keys so that the Burstphase becomes 90° ± 2° as shown in Fig. 4-1-10.8 Press the ENTER key.8 Select the item "8.1. BURST LEVEL R" with the ROLLDOWN key and press the ENTER key.8 Repeat adjustment steps (8.1) to (8.4) until Burst leveland phase are adjusted to proper position as shown inFig. 4-1-7 to Fig. 4-1-10.8 Press the ENTER key for next adjustment.cyg MGYLyl BbG CYdG10°0°10°dø100%75%RVUmgr20%20%dGcyg MGYLyl BbG CYdG10°0°10°dø100%75%RVUmgr20%20%dG135° ± 1° (135° ± 1°)(90° ± 2°) 90° ± 2°NTSC mode PAL modeFig. 4-1-10(9.1) White Balance 3 200°K ManualOffset R AdjustmentTest Point: Video Output Connector8 Keep the Colour Temperature at 3 200°K.8 Aim the Camera at the White Chart or White Paper.8 Set the Gain Control of the Vectorscope to maximum.8 Adjust data with the ARROW keys so that the vector posi-tions at the center of the Vectorscope as shown in Fig. 4-1-11.8 Press the ENTER key for next adjustment.(9.2) White Balance 3 200°K ManualOffset B AdjustmentTest Point: Video Output Connector8 Keep the Colour Temperature at 3 200°K.8 Adjust data with the ARROW keys so that the vector posi-tions at the center of the Vectorscope as shown in Fig. 4-1-11.8 Repeat adjustment steps (9.1) and (9.2) until vector posi-tions at the center of the Vectorscope.8 Press the ENTER key for next adjustment.Fig. 4-1-11cyg MGYLyl BbG CYdG10°0°10°dø100%75%RVUmgr20%20%dGPositions at center.(8.3) Burst Phase R AdjustmentTest Point: Video Output Connector8 Keep the Colour Temperature at 3 200°K.8 Aim the Camera at the Logarithmic Gray Scale Chart.8 Set the Mode Switch of the Vectorscope to NTSC mode.8 Adjust data with the ARROW Keys so that the Burstphase becomes 135° ± 1° as shown in Fig. 4-1-9.8 Change the Mode Switch of the Vectorscope from theNTSC mode to the PAL mode.8 Adjust data with the ARROW Keys so that the Burstphase becomes 90° ± 2° as shown in Fig.4-1-9.8 Press the ENTER key for next adjustment.cyg MGYLyl BbG CYdG10°0°10°dø100%75%RVUmgr20%20%dGcyg MGYLyl BbG CYdG10°0°10°dø100%75%RVUmgr20%20%dG135° ± 1°(90° ± 2°)(135° ± 1°)90° ± 2°PAL modeNTSC modeFig. 4-1-9