Samsung VP-D353 Service Manual

Also see for SC-D351: Owner's manual Owner's instruction manual Owner's instruction book Owner's instruction book Owner's instruction book

Contents

ENGLISH8181USB Interface (VP-D352(i)/D353(i)/D354(i)/D355(i) only)✤ The camcorder supports both USB 1.1 and 2.0 standards. (Depends on the PC specification)✤ You can easily transfer a image from a Memory card to a PC without additional add-on cards via a USB connection.✤ You can transfer a recorded file in memory card to a PC via a USB connection. (VP-D353(i)/D354(i)/D355(i) only)✤ If you transfer data to a PC, you need to install the software (DV Driver, Video Codec , DirectX 9.0) supplied with theCamcorder.High speed USB connection is supported by Microsoft (Windows) device drivers only.■ Windows 98SE/ME - Full Speed USB■ Windows 2000 - High speed USB on a system with Service Pack 4 or later installed.■ Windows XP - High speed USB on a system with Service Pack 1 or later installed.■ It is not available for Macintosh systems.[ Notes ]■ USB 2.0 works only for removable disk functions.■ On a slower PC than recommended, movie playback may not be smooth or video editing may take a long time.■ On a slower PC than recommended, movie playback may skip frames or operate unexpectedly.■ Intel® Pentium III™ or Pentium 4™ is a trademark of the Intel Corporation.■ Windows® is a registered trademark of the Microsoft® Corporation.■ All other brands and names are property of their respective owners.■ Operations are not guaranteed for all of the recommended computer environments mentioned above.■ Do not connect the Camcorder to a PC using both DV and USB cables. It may not operate properly.■ In M.Cam or M.Player mode, be sure that the Memory card is inserted into Camcorder before connecting USB cable.If no Memory card or an unformatted Memory card is inserted, PC will not recognise your Camcorder as a removable disk.(VP-D353(i)/D354(i)/D355(i) only)■ USB Streaming requires Video Codec, DV Driver and DirectX 9.0.■ If you disconnect the USB cable from the PC or the Camcorder during the data transfer, the data transfer will stop and the data may be damaged.■ If you connect the USB cable to a PC using a USB HUB or with other devices at the same time, it may cause conflict and may not work properly.If this occurs, remove all other USB devices and try the connection again.USB Connection speed depending on the SystemSystem RequirementsTransferring a Digital Image through a USB ConnectionCPU Intel® Pentium III™, 600MHz Intel® Pentium 4™ , 2GHzOS(Operating System) Windows® 98SE/ME Windows® 2000/XPMemory 128MB 512MBHDD capacity 1GB or more 2GB or moreResolution 1024 x 768 dots 1024 x 768 dots24bit Colour 24bit ColourUSB USB1.1 USB2.0 High SpeedWindows SystemMinimum RecommendedENGLISH8686USB Interface (VP-D352(i)/D353(i)/D354(i)/D355(i) only)✤ To use USB streaming, the DV Driver, Video Codec and DirectX 9.0. programs must be installed in the PC.✤ You can view Camcorder video on your PC using USB streaming.✤ You can also store it as a moving picture in the "avi" file format, or as a still image in the "jpg" file format on a PC.1. Set the Mode switch to TAPE(VP-D353(i)/D354(i)/D355(i) only), set the Power switch to CAMERA or PLAYER.2. Connect one end of the USB cable to the USB jack on the Camcorder and the other end to the USB port on your computer.3. Setup and execute Windows Movie Maker or the Ulead VIDEO Studio Software application provided on the CD.- For detailed instructions for Ulead VIDEO Studio use, refer to the program’s Help function.- Windows Movie Maker is used for WINDOWS ME and XP users. (C:\program files\Movie maker\moviemk.exe)✤ You can easily transfer data from a Memory card to a PC without additional add-on cards via a USB connection.1. Set the Mode switch to MEMORY CARD, set the Power switch to CAMERA or PLAYER.2. Connect one end of the USB cable to the USB jack on the Camcorder and the other end to the USB port on your computer.3. To verify whether the removable disk has been properly recognised, open Windows Explorer and locate the removable disk.1. Connect a USB cable to the USB port on the PC.■ If a USB cable is connected to the Camcorder's USB port, nothing is displayed on a TV.2. Connect the other end of the USB cable into the USB jack on the Camcorder. (USB jack)■ If a PC is connected to the Camcorder with a USB cable only, Zoom switch and NITE PIX operate.✤ After completing the data transmission, you must disconnect the cable in thefollowing way:1. Select the removable disc icon and click the right mouse button to select [Eject].2. Select [Confirm] and disconnect the USB cable when the Windows Splash screenappears.[ Notes ]■ If you disconnect the USB cable from the PC or the Camcorder while transferring,the data transmission will stop and the data may be damaged.■ If you connect the USB cable to a PC via a USB HUB or simultaneously connect the USB cable along with other USB devices,the Camcorder may not work properly.If this occurs, remove all USB devices from the PC and reconnect the Camcorder.■ While transmitting data from the Camcorder to PC at strong electric field and strong magnetic field, VIDEO signal or AUDIO signalmay transmit with noise.Using the USB Streaming FunctionUsing the removable Disk Function (VP-D353(i)/D354(i)/D355(i) only)Connecting to a PCDisconnecting the USB CableDVUSBAVMICDVUSBAVMICUSB CableOperating Instructions11-8 Samsung Electronics