WAGO WAGO-I/O-SYSTEM 750 Series Manual

Also see for WAGO-I/O-SYSTEM 750 Series: Manual Manual Manual Manual Manual

Contents

WAGO WAGO-I/O-SYSTEM 750 Series Manual Manual pdf 39 page image

WAGO-I/O-SYSTEM 750 Mounting 39750-657 IO-Link MasterManualVersion 1.0.2, valid from FW/HW-Version 02/01Pos: 70 /Alle Serien (Allgemeine Module)/Überschriften für alle Serien/Montieren - Demontieren/Montieren - Überschrift 1 @ 3\mod_1225446744750_21.doc @ 24900 @ 1 @ 17 MountingPos: 71.1 /Serie 750 (WAGO-I/O-SYSTEM)/Montieren/Montagereihenfolge @ 3\mod_1231770210031_21.doc @ 25992 @ 2 @ 17.1 Assembly SequenceAll system components can be snapped directly on a carrier rail in accordancewith the European standard EN 50022 (DIN 35).The reliable positioning and connection is made using a tongue and groovesystem. Due to the automatic locking, the individual components are securelyseated on the rail after installation.Starting with the coupler/controller, the I/O modules are mounted adjacent to eachother according to the project design. Errors in the design of the node in terms ofthe potential groups (connection via the power contacts) are recognized, as the I/Omodules with power contacts (male contacts) cannot be linked to I/O moduleswith fewer power contacts.Pos: 71.2 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- und sonstige Hinweise/Vorsicht/Vorsicht: Verletzungsgefahr durch scharfkantige Messerkontakte! @ 6\mod_1256193279401_21.doc @ 43414 @ @ 1Risk of injury due to sharp-edged male contacts!The male contacts are sharp-edged. Handle the module carefully to prevent injury.Pos: 71.3 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- und sonstige Hinweise/Achtung/Achtung: Busklemmen in vorgegebener Reihenfolge stecken! @ 6\mod_1256194177073_21.doc @ 43429 @ @ 1Connect the I/O modules in the required order!Never plug I/O modules from the direction of the end terminal. A ground wirepower contact, which is inserted into a terminal without contacts, e.g. a 4-channeldigital input module, has a decreased air and creepage distance to the neighboringcontact in the example DI4.Pos: 71.4 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- und sonstige Hinweise/Achtung/Achtung: Aneinanderreihen von Busklemmen nur bei offener Nut! @ 6\mod_1256193351448_21.doc @ 43417 @ @ 1Assemble the I/O modules in rows only if the grooves are open!Please take into consideration that some I/O modules have no or only a few powerjumper contacts. The design of some modules does not allow them to bephysically assembled in rows, as the grooves for the male contacts are closed atthe top.Pos: 71.5 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- und sonstige Hinweise/Hinweis/Hinweis: Busabschluss nicht vergessen! @ 6\mod_1256194225557_21.doc @ 43432 @ @ 1Don't forget the end module!Always plug an end module 750-600 onto the end of the fieldbus node! You mustalways use an end module at all fieldbus nodes with the WAGO I/O System 750fieldbus couplers/controllers to guarantee proper data transfer.Pos: 71.6 /Dokumentation allgemein/Gliederungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1