Manuals database logo
manualsdatabase
Your AI-powered manual search engine

Eaton Sefelec DXS500 manuals

Sefelec DXS500 first page preview

Sefelec DXS500

Brand: Eaton | Category: Test Equipment
Table of contents
  1. This manual is written for the following XS series models
  2. WARRANTY
  3. Restrictions due to the accessories or the options
  4. Table Of Contents
  5. Table Of Contents
  6. Table Of Contents
  7. Table Of Contents
  8. Table Of Contents
  9. Table Of Contents
  10. Specifications
  11. DIELECTRIC STRENGTH TEST 50VA
  12. Maximum current limit : IMAX
  13. Permanent current measurement
  14. µA current resolution (OPTION 116-00)
  15. Output voltage
  18. DIELECTRIC STRENGTH TEST 10VA
  21. Detection of capacitive samples
  22. Megohmmeter function (insulation resistance measurement)
  23. Measurement threshold
  24. V megohmmeter function (option XS26 or MXS1000)
  26. Measurement accuracy
  27. Timer
  28. Ground continuity function
  29. Measurement thresholds
  30. MEANING OF THE DIFFERENT SYMBOLS ON THE INSTRUMENT
  31. PRODUCT OVERVIEW
  32. Front panel description
  33. Liquid Crystal Display (LCD) description
  34. Rear panel description
  35. Available accessories and options
  36. Installation
  37. Power ON
  38. Connection to a specimen
  39. Unit configuration
  40. Beep on FAIL configuration
  41. Access control to the parameters
  42. Measurement display
  43. Remote trigger mode
  44. Interface selection
  45. EXPERT mode Activation
  46. Insulation resistance measurement
  47. Measurement threshold selection
  48. Timer operation
  49. Parameter memorization
  51. Error messages
  52. Dielectric strength test (hipot test)
  53. Test voltage selection
  54. Test voltage application on the specimen
  55. To set the RISE and FALL times
  56. Breakdown detection mode selection
  57. Maximum current and variation current limit : IMAX + I
  58. IMIN and IMAX threshold adjustment
  59. Delta I level adjustment
  61. Activation of the capacitive sample detection
  62. Expert mode parameters only
  63. IMAX and delta I thresholds adjustment during the ramps
  64. Configuration of the minimum capacity value to detect
  65. Dielectric strength test error messages
  66. Ground continuity resistance measurement
  67. Measurement current selection
  68. Resistance threshold selection
  72. Ground continuity measurement error messages
  73. Sequence mode operation (SXS)
  75. Function selection
  76. Parameter memory number selection
  77. How to run a simple sequence
  78. Sequence with manual control
  79. Multiple ground continuity operation
  80. Multiple ground continuity followed by a dielectric strength test ( automatic sequence)
  81. Error messages for the Sequence mode
  82. Accessories with remote control feature
  83. Operation
  84. Specific case for the sequence (SXS50 & 500)
  85. Input output Interfaces
  86. Connections
  87. Description of the input output signals
  88. Measurement discharge cycle
  89. Information on cycle timing
  90. PLC > RS Interface (Option 115-00)
  91. Volts analog input output (03 OPTION )
  92. Change of the board setup
  93. Megohmmeter mode, 2 outputs setup
  94. Dielectric strength test mode, 2 outputs setup
  95. Operating instructions
  96. IEEE-488 interface
  97. Commands
  98. ETHERNET Interface
  99. How to set the Ethernet interface card under Windows XP
  100. Configuring the connexion on the unit
  101. Protocol and communication port
  102. List of the ETHERNET commands
  103. Error message(s)
  104. RS232C interface
  105. Syntax rules
  106. List of the RS232C commands
  107. Advices and programming examples
  108. Trouble shooting the RS232 interface
  109. APPLICATION NOTES
  110. Environmental influences
  111. Precautions to be observed
  112. Measurements on cables
  113. Dielectric strength tests
  115. Ground continuity measurement
  117. Safety interlock connector (C5)
  118. Measurement I/O on the rear panel
  119. Maintenance and calibration
  120. CLEANING
  121. Annexes
  122. wires option for XS series and hipot function
  123. Operation of the XS 4-wire option in XS hipot function
  124. Schematic diagram of the option
  125. Uses cases
  126. HV sensor connection recommendations
  127. Rear view of the unit and accessory connections
  128. Nominal DC currents in the hipot function
  129. XS 500VA DC current curves (RXS506, DXS506, SXS506)
Related products
Sefelec DXS50Sefelec DXS506Sefelec SXS500Sefelec DXS56Sefelec MXS500Sefelec RXS500Sefelec SXS50Sefelec RXS50Sefelec SXS506Sefelec RXS506
Eaton categories
Circuit breakers
Industrial Equipment
Industrial Electrical
UPS
Switch
Control Unit
Controller
Accessories
Relays
Water Pump
More Eaton categories
Manuals database logo
manualsdatabase
Your AI-powered manual search engine