Genie Z-34/22 manuals
Z-34/22
Table of contents
- April
- safety rules
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Specifications
- Hydraulic Component Specifications
- Machine Torque Specifications
- Hydraulic Hose and Fitting Torque Specifications
- Torque Procedure
- Scheduled Maintenance Procedures
- Pre-Delivery Preparation Report
- Maintenance Inspection Report
- Checklist A Procedures
- A-2 Perform Pre-operation Inspection
- A-6 Perform 30 Day Service
- A-8 Perform Engine Maintenance
- A-10 Grease the Turntable Rotation Bearing and Worm Drive Gear
- A-11 Replace the Drive Hub Oil
- A-12 Perform Engine Maintenance
- Checklist B Procedures
- B-3 Inspect the Electrical Wiring
- B-4 Inspect the Tires, Wheels and Lug Nut Torque
- B-7 Check the Glow Plugs
- B-8 Check and Adjust the Engine RPM
- B-9 Test the Ground Control Override
- B-11 Test the Engine Idle Select
- B-12 Test the Drive Brakes
- B-14 Test the Drive Speed - Raised or Extended Position
- B-15 Test the Alarm Package (if equipped)
- B-16 Check the Electrical Contactors
- B-18 Perform Hydraulic Oil Analysis
- B-19 Test the Emergency Power System
- B-20 Perform Engine Maintenance
- C-3 Perform Engine Maintenance
- Checklist D Procedures
- D-3 Inspect for Turntable Bearing Wear
- D-4 Check the Free-wheel Configuration
- D-5 Replace the Drive Hub Oil
- Checklist E Procedures
- E-2 Grease the Steer Axle Wheel Bearings, 2WD Models
- E-3 Perform Engine Maintenance
- Section 4 Repair Procedures
- repair procedures
- Platform Controls
- Diodes
- Toggle Switches
- Platform Rotator
- How to Bleed the Platform Rotator
- Platform Overload System
- platform components
- Jib Boom Components
- Jib Boom Bell Crank
- Primary Boom Components
- How to Disassemble the Primary Boom
- Primary Boom Lift Cylinder
- Primary Boom Extension Cylinder
- Platform Leveling Master Cylinder
- Secondary Boom Components
- Secondary Boom
- Secondary Boom Lift Cylinders
- Engines
- How to Install the Engine Drive Pulley
- Coolant Temperature and Oil Pressure Switches
- Generator
- Generator Belts
- Generator Voltage Regulator
- How to Replace the Voltage Regulator
- Hydraulic Pumps
- Function Pump
- Manifolds
- Valve Adjustments - Function Manifold
- How to Adjust the Secondary Boom Down Relief Valve
- Jib Boom / Platform Rotate Manifold Components
- Valve Coils
- How to Test a Coil Diode
- Fuel and Hydraulic Tanks
- Turntable Rotation Components
- Axle Components
- How to Install the Hub and Bearings
- Non-steer Axle Components
- Motor Controller
- Fault Code Charts
- Section 6 Schematics
- Electrical Symbol Legend
- Hydraulic Symbols Legend
- Electrical Schematic - from serial number 4800 to 5426 (ANSI / CSA)
- Electrical Schematic - from serial number 4800 to 5426 (CE)
- Electrical Schematic - from serial number 5427 to 9441 (ANSI / CSA)
- Electrical Schematic - from serial number 9442 to 9685 (ANSI / CSA)
- Electrical Schematic - from serial number 5427 to 9441 (CE)
- Electrical Schematic - from serial number 9442 to 9685 (CE / AS)
- Ground Control Box Switch Panel Wiring Diagram
- Ground Control Box Terminal Strip Wiring Diagram
- Ground Control Box Terminal Strip Wiring Diagram - from serial number 9442 to 9685 (ANSI/CSA)
- Ground Control Box Terminal Strip Wiring Diagram - from serial number 9442 to 9685 (CE / AS)
- Platform Control Box Wiring Diagram
- Power Cable Wiring Diagram
- Drive Contactor Panel Wiring Diagram
- Manifold and Limit Switch Wiring Diagram
- LVI / BCI Option Wiring Diagram, from serial number 4800 to 5426
- LVI / BCI Option Wiring Diagram, from serial number 5427
- Engine Wiring Diagram
- Hydraulic Schematic
manualsdatabase
Your AI-powered manual search engine