Canon MF6500 Series Service Manual

Also see for imageCLASS MF6500 Series: Basic guide Starter Guide Driver guide Advanced guide Software guide

Contents

Chapter 1313-213.2 Jam Code13.2.1 Jam Codes (Main body) 0011-7062LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PLT-13-213.2.2 Jam Codes (ADF) 0011-7059LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PLT-13-313.3 Fax Error Codes13.3.1 Outline13.3.1.1 Error Code Outline 0012-5780LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PLAn error code is used to indicate a fault in a machine, and is indicated in the machine's LCD or reports, showing the nature (symptoms) of the fault. Using the errorcode, the user or the service man can readily find out how to correct the fault by simply referring to the User's Manual or service manual.An error code may be either of the following two types:User Error CodesA fault indicated as a user error code is one that can easily be corrected by the user, as by operating the machine. It takes the form of "#+number."Service Error CodesIf a fault calls for a service man for correction, it is indicated as a service man error code in the form of "##+number" or "SYSTEM ERROR E+number."MemoA service error code expressed in the form of "##+number" will not appear on the LCD, Error Tx Report, or Activity Report while the machine remainsin factory default state. To check a service error code, shift bit 0 of service soft switch #1 SSSW SW01 to '1'.MemoDisplay only the error codes which are newly incorporated in this machine as well as which require remedies unique to the product. For the causes andcountermeasures of other error codes, refer to the separate G3/G4 Facsimile Error Code List (Rev. 2).13.3.2 User Error Code13.3.2.1 User Error Code 0012-5781LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PLT-13-4Code Name Sensor No. Description0104 Delay jam in paper pickupsectionSR11 The registration sensor cannot detect the leading edge of paper from the moment paper pickup startsto the moment the jam detection time is reached.0208 Stationary jam in paperpickup sectionSR11 The registration sensor cannot detect the no paper status specified time before the leading edge ofthe picked up paper reaches this sensor.010c Delay jam in deliver section SR5 - The delivery sensor cannot detect presence of paper within the specified time after turning on ofthe registration clutch.- The delivery sensor detected absence of paper within the specified time after the sensor haddetected presence of paper within the specified time after turning on of the registration clutch.0210 Stationary jam in deliverysectionSR5 - The delivery sensor cannot detect absence of paper within the specified time after turning off ofthe registration clutch.- The delivery sensor cannot detect absence of paper within the specified time after the sensordetected the leading edge of paper.0214 Stationary jam in machine SR5, SR9 Paper was detected in the paper transport path during initial rotation, during automatic delivery, atthe end of cleaning, or at reception of an emergency stop command.1118 Door open jam SW2, SR5, SR9,SR11The door was opened when there was printing paper in the transport path.Code Name Sensor No. Description0000 Unknown jam - Other errors0007 Initial stationary SR2002, SR2003, SR2004 Paper is detected in the transport path before the DADF starts initialoperation.0008 Document edge sensordelaySR2002 The document edge sensor does not detect paper when the paper has been fed by thepredetermined distance since reception of a pickup request.0009 Document edge sensorstationarySR2002 The trailing edge of paper is not detected when the paper has been fed by thepredetermined distance since detection of it by the document edge sensor.000a Paper absence (Pull outthe document.)SR2001 The Document set sensor has been held off since start of pickup.0010 Pickup NG SR2003 The registration sensor has been held off since paper pickup started.No. Tx/Rx Description#0001 [Tx] an original has jammed.#0003 [Tx/Rx] tine-out for copying or sending/receiving a single page has occurred.#0005 [Tx/Rx] time-out for initial identification (T0/T1) has occurred.#0009 [Rx] recording paper has jammed or is absent.#0012 [Tx] recording paper is absent at the other party.Download Free Service Manual And Resetter Printer at http://printer1.blogspot.com