Origin codes: i - IGP, e - EGP, ? - incompleteNetwork Next Hop Metric LocPrf Weight Path* i 3.0.0.0/8 195.171.0.16 100 0 209 701 80 i*>i 4.2.49.12/30 195.171.0.16 100 0 209 i* i 4.21.132.0/23 195.171.0.16 100 0 209 6461 16422 i*>i 4.24.118.16/30 195.171.0.16 100 0 209 i*>i 4.24.145.0/30 195.171.0.16 100 0 209 i*>i 4.24.187.12/30 195.171.0.16 100 0 209 i*>i 4.24.202.0/30 195.171.0.16 100 0 209 i*>i 4.25.88.0/30 195.171.0.16 100 0 209 3561 3908 i*>i 6.1.0.0/16 195.171.0.16 100 0 209 7170 1455 i*>i 6.2.0.0/22 195.171.0.16 100 0 209 7170 1455 i*>i 6.3.0.0/18 195.171.0.16 100 0 209 7170 1455 i*>i 6.4.0.0/16 195.171.0.16 100 0 209 7170 1455 i*>i 6.5.0.0/19 195.171.0.16 100 0 209 7170 1455 i*>i 6.8.0.0/20 195.171.0.16 100 0 209 7170 1455 i*>i 6.9.0.0/20 195.171.0.16 100 0 209 7170 1455 i*>i 6.10.0.0/15 195.171.0.16 100 0 209 7170 1455 i*>i 6.14.0.0/15 205.171.0.16 100 0 209 7170 1455 i*>i 6.133.0.0/21 205.171.0.16 100 0 209 7170 1455 i*>i 6.151.0.0/16 205.171.0.16 100 0 209 7170 1455 i--More--Changing MED AttributesBy default, Dell Networking OS uses the MULTI_EXIT_DISC or MED attribute when comparing EBGP paths from the same AS.To change how the MED attribute is used, enter any or all of the following commands.• Enable MED comparison in the paths from neighbors with different ASs.CONFIG-ROUTER-BGP modebgp always-compare-medBy default, this comparison is not performed.• Change the bestpath MED selection.CONFIG-ROUTER-BGP modebgp bestpath med {confed | missing-as-best}– confed: Chooses the bestpath MED comparison of paths learned from BGP confederations.– missing-as-best: Treat a path missing an MED as the most preferred one.To view the nondefault values, use the show config command in CONFIGURATION ROUTER BGP mode.Changing the LOCAL_PREFERENCE AttributeIn Dell Networking OS, you can change the value of the LOCAL_PREFERENCE attribute.To change the default values of this attribute for all routes received by the router, use the following command.• Change the LOCAL_PREF value.CONFIG-ROUTER-BGP modebgp default local-preference value– value: the range is from 0 to 4294967295.The default is 100.To view the BGP configuration, use the show config command in CONFIGURATION ROUTER BGP mode or the showrunning-config bgp command in EXEC Privilege mode.Border Gateway Protocol IPv4 (BGPv4) 183
