Monitor Port-ChannelsTo check the status of a Layer 2 port-channel, use f10LinkAggMib (.1.3.6.1.4.1.6027.3.2). In the following example, Po 1 is a switchportand Po 2 is in Layer 3 mode.Example of SNMP Trap for Monitored Port-Channels[senthilnathan@lithium ~]$ snmpwalk -v 2c -c public 10.11.1.1 .1.3.6.1.4.1.6027.3.2.1.1SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.1.1 = INTEGER: 1SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.1.2 = INTEGER: 2SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.2.1 = Hex-STRING: 00 01 E8 13 A5 C7SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.2.2 = Hex-STRING: 00 01 E8 13 A5 C8SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.3.1 = INTEGER: 1107755009SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.3.2 = INTEGER: 1107755010SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.4.1 = INTEGER: 1SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.4.2 = INTEGER: 1SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.5.1 = Hex-STRING: 00 00SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.5.2 = Hex-STRING: 00 00SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.6.1 = STRING: "Gi 5/84 " << Channel member for Po1SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.6.2 = STRING: "Gi 5/85 " << Channel member for Po2dot3aCommonAggFdbIndexSNMPv2-SMI::enterprises.6027.3.2.1.1.6.1.1.1107755009.1 = INTEGER: 1107755009dot3aCommonAggFdbVlanIdSNMPv2-SMI::enterprises.6027.3.2.1.1.6.1.2.1107755009.1 = INTEGER: 1dot3aCommonAggFdbTagConfigSNMPv2-SMI::enterprises.6027.3.2.1.1.6.1.3.1107755009.1 = INTEGER: 2 (Tagged 1 or Untagged2)dot3aCommonAggFdbStatusSNMPv2-SMI::enterprises.6027.3.2.1.1.6.1.4.1107755009.1 = INTEGER: 1 << Status active, 2 –status inactiveExample of Viewing Status of Learned MAC AddressesIf we learn MAC addresses for the LAG, status is shown for those as well.dot3aCurAggVlanIdSNMPv2-SMI::enterprises.6027.3.2.1.1.4.1.1.1.0.0.0.0.0.1.1 = INTEGER: 1dot3aCurAggMacAddrSNMPv2-SMI::enterprises.6027.3.2.1.1.4.1.2.1.0.0.0.0.0.1.1 = Hex-STRING: 00 00 00 00 00 01dot3aCurAggIndexSNMPv2-SMI::enterprises.6027.3.2.1.1.4.1.3.1.0.0.0.0.0.1.1 = INTEGER: 1dot3aCurAggStatusSNMPv2-SMI::enterprises.6027.3.2.1.1.4.1.4.1.0.0.0.0.0.1.1 = INTEGER: 1 << Status active, 2– statusinactiveExample of Viewing Changed Interface State for Monitored PortsLayer 3 LAG does not include this support. SNMP trap works for the Layer 2 / Layer 3 / default mode LAG.SNMPv2-MIB::sysUpTime.0 = Timeticks: (8500842) 23:36:48.42SNMPv2-MIB::snmpTrapOID.0 = OID: IF-MIB::linkDownIF-MIB::ifIndex.33865785 = INTEGER: 33865785SNMPv2-SMI::enterprises.6027.3.1.1.4.1.2 = STRING: "OSTATE_DN: Changed interface state todown: Te 1/1"2010-02-10 14:22:39 10.16.130.4 [10.16.130.4]:SNMPv2-MIB::sysUpTime.0 = Timeticks: (8500842) 23:36:48.42SNMPv2-MIB::snmpTrapOID.0 = OID: IF-MIB::linkDownIF-MIB::ifIndex.1107755009 = INTEGER: 1107755009SNMPv2-SMI::enterprises.6027.3.1.1.4.1.2 = STRING: "OSTATE_DN: Changed interface state todown: Po 1"2010-02-10 14:22:40 10.16.130.4 [10.16.130.4]:SNMPv2-MIB::sysUpTime.0 = Timeticks: (8500932) 23:36:49.32 SNMPv2-MIB::snmpTrapOID.0 = OID:IF-MIB::linkUp IF-MIB::ifIndex.33865785 = INTEGER: 33865785 SNMPv2-SMI::enterprises.6027.3.1.1.4.1.2 =STRING: "OSTATE_UP: Changed interface state to up: Te 1/1"2010-02-10 14:22:40 10.16.130.4 [10.16.130.4]:SNMPv2-MIB::sysUpTime.0 = Timeticks: (8500934) 23:36:49.34 SNMPv2-MIB::snmpTrapOID.0 = OID:IF-MIB::linkUp IF-MIB::ifIndex.1107755009 = INTEGER: 1107755009708 Simple Network Management Protocol (SNMP)
