dot3aCommonAggFdbVlanIdSNMPv2-SMI::enterprises.6027.3.2.1.1.6.1.2.1107755009.1 = INTEGER: 1dot3aCommonAggFdbTagConfigSNMPv2-SMI::enterprises.6027.3.2.1.1.6.1.3.1107755009.1 = INTEGER: 2 (Tagged 1or Untagged 2)dot3aCommonAggFdbStatusSNMPv2-SMI::enterprises.6027.3.2.1.1.6.1.4.1107755009.1 = INTEGER: 1 << Statusactive, 2 – status inactiveExample of Viewing Status of Learned MAC AddressesIf we learn MAC addresses for the LAG, status is shown for those as well.dot3aCurAggVlanIdSNMPv2-SMI::enterprises.6027.3.2.1.1.4.1.1.1.0.0.0.0.0.1.1 = INTEGER: 1dot3aCurAggMacAddrSNMPv2-SMI::enterprises.6027.3.2.1.1.4.1.2.1.0.0.0.0.0.1.1 = Hex-STRING: 00 0000 00 00 01dot3aCurAggIndexSNMPv2-SMI::enterprises.6027.3.2.1.1.4.1.3.1.0.0.0.0.0.1.1 = INTEGER: 1dot3aCurAggStatusSNMPv2-SMI::enterprises.6027.3.2.1.1.4.1.4.1.0.0.0.0.0.1.1 = INTEGER: 1 <<Status active, 2 – statusinactiveExample of Viewing Changed Interface State for Monitored PortsLayer 3 LAG does not include this support. SNMP trap works for the Layer 2 / Layer 3 / default mode LAG.SNMPv2-MIB::sysUpTime.0 = Timeticks: (8500842) 23:36:48.42SNMPv2-MIB::snmpTrapOID.0 = OID: IF-MIB::linkDownIF-MIB::ifIndex.33865785 = INTEGER: 33865785SNMPv2-SMI::enterprises.6027.3.1.1.4.1.2 = STRING: "OSTATE_DN: Changedinterface state to down: Te 1/1"2010-02-10 14:22:39 10.16.130.4 [10.16.130.4]:SNMPv2-MIB::sysUpTime.0 = Timeticks: (8500842) 23:36:48.42SNMPv2-MIB::snmpTrapOID.0 = OID: IF-MIB::linkDownIF-MIB::ifIndex.1107755009 = INTEGER: 1107755009SNMPv2-SMI::enterprises.6027.3.1.1.4.1.2 = STRING: "OSTATE_DN: Changedinterface state to down: Po 1"2010-02-10 14:22:40 10.16.130.4 [10.16.130.4]:SNMPv2-MIB::sysUpTime.0 = Timeticks: (8500932) 23:36:49.32 SNMPv2-MIB::snmpTrapOID.0 = OID:IF-MIB::linkUp IF-MIB::ifIndex.33865785 = INTEGER: 33865785 SNMPv2-SMI::enterprises.6027.3.1.1.4.1.2 =STRING: "OSTATE_UP: Changed interface state to up: Te 1/1"2010-02-10 14:22:40 10.16.130.4 [10.16.130.4]:SNMPv2-MIB::sysUpTime.0 = Timeticks: (8500934) 23:36:49.34 SNMPv2-MIB::snmpTrapOID.0 = OID:IF-MIB::linkUp IF-MIB::ifIndex.1107755009 = INTEGER: 1107755009SNMPv2-SMI::enterprises.6027.3.1.1.4.1.2 = STRING: "OSTATE_UP: Changedinterface state to up: Po 1"Troubleshooting SNMP OperationWhen you use SNMP to retrieve management data from an SNMP agent on a Dell Networking router,take into account the following behavior.• When you query an IPv4 icmpMsgStatsInPkts object in the ICMP table by using the snmpwalkcommand, the output for echo replies may be incorrectly displayed. To correctly display thisinformation under ICMP statistics, use the show ip traffic command.804 Simple Network Management Protocol (SNMP)
