Eaton PowerXL DF1 Series User Manual

2465. Parameter DescriptionEaton Electric General Inverters DF1 Series UMXXXXXXXXE February 2020 www.eaton.comAs shown in the above, the single point positioning function can be described as follows:In closed loop speed mode, set the external terminals can function as the single point positioning make (example03-03 (P. 80) = 68), when DI4 terminal OFF, is pure speed mode, when DI4 terminal ON inverter from the currentoperating frequency curve acceleration and deceleration, run to locate frequency parameters (12-12 set), located in thefrequency of operation, until the Z phase was detected, will switch to the value is set to 12-11 position control of thetarget location (position control process not deceleration curve), the position control gain (12-05 (P. 425)), arriving posi-tion output terminal and position allowance (12-09 (P. 429)) and Pt, Pr position mode share.5.13.5 Position command• Set the position command value in position control mode via parameter with the digital input terminal state.Parameter Name FactoryValueSettingRange Content12-20P.450Number of turnsposition command 1 0 -30000~30000 Terminal state Target position upperlimit offrequencyREX RH RM RL Rotation turns+ number ofpulses00 0 0 00 1 0 0 Position1 12-20 12-21 Speed 10 0 1 0 Position2 12-22 12-23 Speed 20 0 0 1 Position3 12-24 12-25 Speed 30 0 1 1 Position4 12-26 12-27 Speed 40 1 0 1 Position5 12-28 12-29 Speed 50 1 1 0 Position6 12-30 12-31 Speed 60 1 1 1 Position7 12-32 12-33 Speed 71 0 0 0 Position8 12-34 12-35 Speed 81 0 0 1 Position9 12-36 12-37 Speed 91 0 1 0 Position10 12-38 12-39 Speed 101 0 1 1 Position11 12-40 12-41 Speed 111 1 0 0 Position12 12-42 12-43 Speed 121 1 0 1 Position13 12-44 12-45 Speed 131 1 1 0 Position14 12-46 12-47 Speed 141 1 1 1 Position15 12-48 12-49 Speed 1512-21P.451Number of pulsesposition command 1 0 -30000~3000012-22P.452Number of turnsposition command 2 0 -30000~3000012-23P.453Number of pulsesposition command 2 0 -30000~3000012-24P.454Number of turnsposition command 3 0 -30000~3000012-25P.455Number of pulsesposition command 3 0 -30000~3000012-26P.456Number of turnsposition command 4 0 -30000~3000012-27P.457Number of pulsesposition command 4 0 -30000~3000012-28P.458Number of turnsposition command 5 0 -30000~3000012-29P.459Number of pulsesposition command 5 0 -30000~3000012-30P.460Number of turnsposition command 6 0 -30000~3000012-31P.461Number of pulsesposition command 6 0 -30000~3000012-32P.462Number of turnsposition command 7 0 -30000~3000012-33P.463Number of pulsesposition command 7 0 -30000~3000012-34P.464Number of turnsposition command 8 0 -30000~3000012-35P.465Number of pulsesposition command 8 0 -30000~3000012-36P.466Number of turnsposition command 9 0 -30000~3000012-37P.467Number of pulsesposition command 9 0 -30000~30000