Garland MWE2W Installation, Operation & Service Manual
Also see for MWE1S: STEPS FOR PROGRAMMING GRILL RECOVERY CLEANINGProgramming instructionsProgramming Instruction
                                                                                              | |
Contents
|
INSTALLATION/OPERATION & SERVICE MANUAL - 1&2 PLATEN GARLAND CLAMSHELL GRILLS WITH PRODUCT RECOGNITIONPART #4527466 (12 Aug 2011)Page 48SOFTWARE V222System Menu Sub Menu Options Description of Options DefaultConfigure MenuElectricGasYesNoWorldJapanTime Then AlarmJapan Fixed 10SLeftCenterRightYesNoOnOffAuto Standby Delay 1-5 Seconds in which alarm will sound when alerting operator to put grill in standby. 3SetupTemperature Units F (Fahrenheit)C (Celcius)Time Unit sssmssmmmKey Chirp YesNoAudible 3 SecondStrobeSongAudio Volume 1-100 (Adjustable) Alarm volume 100Reload Defaults YesNoMulti Gap YesNoAudible Select 012Auto Mode Enable YesNoProduct Rec Timeout 0-30Maximum number of seconds to recognize product. If product is not recognized in [Product Rec Timout} time, then "Product NotRec" 10Heater Err Timer 60-1200 Number of seconds the controller must see a temperature rise before "Heater Error" 425Too Cool Lo Lmt OFF, 1F/C-450F / 250C 110F / 61CCalibrationLevel / Reed Switch YesNoAuto Gap Force YesNoProbe Cal All Temperature Zones Mode to perform a temperature probe calibrationGap Calibration -1000 - 1000 Gap Offset - Offsets Gap setting for all menu items. 0Reed Switch Min 0 - 1000 Maximum Δ CAL before warning / error msg 200Reed Switch Max 0 - 1000 Maximum Δ CAL before disabling clam operation. 300Delta Speed Err 0-20Number corresponds to linear actuator motor speed.Adjusts automatically.Pivot End Mills 800 - 3000 Number set corresponds to location of pivot block to determine pivot point and decreased motor speed. 1100Show Reed Data YES/NO When activated to YES, controller will display encoder counts when reed switches close. NoFront Reed Cal XXX During Auto Calibration, the encoder counts when Front Reed Switch Closed.Back Reed Cal XXX During Auto Calibration, the encoder counts when Back Reed Switch Closed.F ZERO Cal XXX During Auto Calibration, the encoder counts when Front Reed Switch Opened.B ZERO Cal XXX During Auto Calibration, the encoder counts when Back Reed Switch Opened.F ARM OFFSET_MIN -3000 - 1000 Calculated Offset of arm deflection. -20Cal Delta Percent XXX Factor of error calculated in control. 25%Diagnostic Date Code YYDDD Date-of manufacturerSerial Number XXXXXX Serial No.Part Number N3AF-XXX-XXX Control Part Number N2AF-0307-CNTLApp VERSION XX.XX.XXX Software Revision Number 04.01.202CLM 1 Version XX.XX.XXX Control Loop Module Revision 1 01.00.046CLM 2 Version XX.XX.XXX Control Loop Module Revision 2 01.00.046Audio Version XX.XX.XXX Audio Code Revision 01.00.018Motor Version XX.XX.XXX Motor Control Revision Number 06.00.034Ambient 1 XXXX F/C Actual Internal Temperature AmbientAmbien 2 XXXX F/C Actual Internal Temperature Ambient (With Offset)Ambient 3 XXXX F/C Actual Internal Temperature Ambient (With Offset)Top Probe XXXX F/C Actual Temperature Top ProbeGrill Probe F XXXX F/C Actual Temperature Front ProbeGrill Probe M XXXX F/C Actual Temperature Middle ProbeGrill Probe B XXXX F/C Actual Temperature Back ProbeExternal probe XXXX F/C Actual Temperature External Probe OFFPR Front Detect XXX Last PR Value Detected By Front Reed SwitchPR Back Detect XXX Last PR Value Detected By Backt Reed SwitchPR Table Value XXX Last PR Table Value CalculatedService Encoder Counts 87-3500 Encoder Counts Brom Bottom Limit Sw Top Limit SwMotor Status xxx Motor status Code - Operating Parameter 15Switch Status xxx Switch Status Code - Operating ParameterStartup Rate x Startup Rate Code - Operating Parameter 8Buss Voltage 198 +/- 10% Controller Buss VoltageMotor Max Speed 64 Motor Max Speed Code 64Motor Revision xxx Motor Revision 152Motor Error x Motor Error Code - Operating Parameter 0Lonworks Service Yes / No Lonworks Activated NOMode where user can perform an Auto Calibration upon request. No1YesMode where technician performs Platen Leveling procedure, and Reed Switch Calibration procedure NoPitch of tone in controllerEnables or disables product recognition cooking in control.YesYesOFFFsssEnabled Multi Gap cooking on or off.Setting to display temperature units in Fahrenheit or Celcius.Setting to display time Units:sss - Secondsmss - Minutes / Seconds (M:SS)Setting that turns the sound on/off when a button is pressed.Audible sound when remove alarm is sounding.ElectricYesWorldLeftWhen Yes is selected, the control will automatically begin to reload its factory defaults. In this setting, only menu item defaults arereloaded.Yes3 secondNoGrill RegionCook ZoneSetting to determine regional setup requirements.Placement of control on grill.Setting that tells control whether grill is electric or gas. Must be set correctly to identify number of heat zones.Setting in control that tells whether platen is present. I.E: Flat grills (No Platens).Grill TypePlaten EnabledTime ThenCurrent requirements are for 2 stages of gap. This setting when set to Yes shows all 3 additional multi gap settings.Turns on/off the automatic alarm to alert the operator to put grill in standby.More Multi GapAuto Standby TimerRemove AlarmFUNCTION OPTIONS; SYSTEM MENUS |
Related manuals for Garland MWE1S
manualsdatabase
Your AI-powered manual search engine