Contents - Introduction
- June 2012
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- GS-30 • GS-32 • GS-46 • GS-47 Part
- Machine Specifications
- Performance Specifications
- GS-2032 and
- Hydraulic Specifications
- Manifold Component Specifications
- Hydraulic Hose and Fitting Torque Specifications
- Pre-delivery Preparation Report
- Maintenance Inspection Report
- A-1 Inspect the Manuals and Decals
- A-2 Perform Pre-operation Inspection
- A-4 Perform 30 Day Service
- B-1 Inspect the Batteries
- B-2 Inspect the Electrical Wiring
- B-3 Inspect the Electrical Contactor
- B-5 Test the Emergency Stop
- B-6 Test the Key Switch
- B-8 Test the Drive Brakes
- B-12 Perform Hydraulic Oil Analysis
- B-14 Check the Module Tray Latch Components
- B-15 Inspect the Voltage Inverter (if equipped)
- B-17 Test the Up Limit Switch (if equipped and the Maximum Drive Height Limit Switches (if equipped)
- C-1 Test the Platform Overload Pressure Transducer and Platform Height Sensor (if equipped)
- C-2 Calibrate the Platform Overload System (if equipped)
- C-3 Replace the Hydraulic Tank Breather Cap Models with Optional Hydraulic Oil
- D-1 Check the Scissor Arm Wear Pads
- D-2 Replace the Hydraulic Tank Return Filter Element
- E-1 Test or Replace the Hydraulic Oil
- Circuit Boards
- Joystick
- Platform Emergency Stop Button
- Software Revision Level
- Machine Setup
- Manual Platform Lowering Cable
- Level Sensors
- Outrigger Calibration
- Hydraulic Tank
- Function Pump
- Function Manifold Components GS-1530, GS-1532, GS-1930 and GS-1932
- Function Manifold Components GS-2032, GS-2632, GS-3232, GS-2046, GS-2646 and GS-3246
- Function Manifold Components GS-4047
- Check Valve Manifold Components GS-1530, GS-1532, GS-1930 and GS-1932
- Lift Pressure Selector Manifold Components - GS-4047
- Outrigger Function Manifold Components - GS-3232
- Outrigger Cylinder Manifold Components - GS-3232
- Valve Adjustments - Function Manifold
- Valve Coils
- Yoke and Drive Motor
- Steer Cylinder
- Steer Bellcrank
- Drive Brake
- Brake Release Hand Pump Components
- Scissor Assembly, GS-1530 and GS-1532
- Scissor Assembly, GS-1930 and GS-1932
- Scissor Assembly, GS-2032 and GS-2046
- Scissor Assembly, GS-2632 and GS-2646
- Scissor Assembly, GS-3232 and GS-3246
- Scissor Assembly, GS-4047
- Platform Height Sensor
- Lift Cylinder
- GS-2046 and
- Pressure Transducer
- Platform Overload System
- Platform
- Platform Extension
- GCON I/O Map without Load Sense - (GS-3232 only)
- GCON I/O Map with Load Sense (GS-3232 only)
- Operational Indicator Codes
- Fault Inspection Procedure
- Type "HXXX" Faults
- Type "PXXX" Faults
- Type "UXXX" Faults
- Type "FXXX" Faults
- Type "CXXX" Faults
- Limit Switch Legend
- Electrical Symbols Legend
- from serial number
- GS-2046, GS-2646 and
|
Section 4 • Repair ProceduresJanuary 2012Part No. 228901 GS-30 • GS-32 • GS-46 • GS-47 4 - 119Platform Components10-1PlatformHow to Remove the PlatformPerform this procedure with the platform extensionfully retracted and locked in position.1 Raise the platform to approximately 3 ft / 1 m.2 Remove the retaining fasteners securing theplatform to the platform mount at the steer endof the machine.3 Lower the platform to the stowed position.4 Disconnect the battery packs from the machine.Electrocution/burn hazard. Contactwith electrically charged circuitscould result in death or seriousinjury. Remove all rings, watchesand other jewelry.5 Disconnect the platform controls from thecontrol cable at the platform.6 Remove the cover from the AC outlet. Tag anddisconnect the wiring from the outlet.Electrocution hazard. Contact withelectrically charged circuits couldresult in death or serious injury.Remove all rings, watches andother jewelry.7 Disconnect the wiring from the platform and pullthe wiring free of the platform.8 Models with air line to platform option:Disconnect the air line from the platform. Pullthe air line free of the platform.9 Support the platform with a forklift at thenon-steer end. Do not apply any liftingpressure.10 Attach a strap from the lanyard anchorage pointon the platform railings to the carriage on theforklift to help support the platform.11 GS-1530/32 and GS-1930/32: Lift the steer endof the platform slightly to clear the platformmount and slide the platform towards the non-steer end of the machine until the platform slideblocks at the non-steer end of the machine arevisible through the access holes in the bottomof the platform.All other models: Lift the steer end of theplatform slightly to clear the platform mount andslide the platform towards the steer end of themachine until the platform slide blocks at thenon-steer end of the machine are visiblethrough the access holes in the bottom of theplatform.Crushing hazard. The platform willfall if not properly supported.12 Carefully lift the platform off of the machine andplace it on a structure capable of supporting it.Note: Take notice of the wear pad position beforethe platform is removed. Correct wear pad positionis essential for proper platform functionality.
|
