Contents - Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- ENERGY STAR
- Communication Statements
- European Union (EC) Electromagnetic Compatibility Directives
- Electrical Safety
- Trademarks and Service Marks
- Safety Inspection
- Inspect Mechanical Parts
- Inspect Electrical Parts
- Preface
- Printing Conventions In This Manual
- Related Documents
- About The Printer
- How To Identify The Printer
- Printer Configuration Code
- Forms Handling
- Important Maintenance Notes
- Controls And Indicators
- Mechanical Controls: Figure 6
- Diagnosing Problems
- Start Of Call
- How To Troubleshoot
- Troubleshooting Display Messages
- Operator Panel Message 301 - 305
- Troubleshooting Other Symptoms
- Communication Problems
- General Symptom List
- operator panel
- power stacker
- print quality
- printer operation
- Diagnostics
- Operator Print Tests
- Selecting And Running Tests
- Customer Engineer (CE) Tests
- Boot Diagnostics Menu
- Hex Code Printout
- Printer Information Menu
- Soft vs. Hard Reset
- Controller Board Status LEDs At Power Up
- Troubleshooting A New Installation
- RibbonMinder
- ribbon action
- The Ribbon Log
- Downloading Microcode From IBM First
- Clear NVRAM
- Loading Flash Memory
- Loading Through The Serial Or Parallel Port
- Loading Through the Network Interface Card (NIC)
- Reprogramming the Security Key
- Shuttle Electrical Shorts Test
- Hammer Bank Power Cable Shorts Test
- Cable Shorts Test
- Main Wire Harness Test Diagnostic
- Power Supply Operational Check
- Locations
- Circuit Diagrams, Circuit Boards, Cables, and Switches
- interconnection diagram
- power distribution diagram
- Removals and Adjustments
- Preparing The Printer For Maintenance
- Restoring The Printer To Operation
- Removal And Replacement Procedures
- Belt, Paper Feed Timing
- Belt, Platen Open
- Circuit Board: PSA3 Controller
- Circuit Board: Power Supply
- Circuit Breaker
- Connector Shells
- Cover Assembly, Hammer Bank / Ribbon Mask
- Cover Assembly, Shuttle
- Cover Assembly, Top, Pedestal Model
- Dashpot
- Ethernet Interface Assembly
- Fan Assembly, Cabinet Exhaust
- Fan Assembly, Card Cage
- Fan Assembly, Hammer Bank
- Hammer Spring Assembly
- IBM Coax/Twinax Expansion Board
- Magnetic Pick-up (MPU) Assembly
- Memory Modules and Security Key
- Motor Assembly, Paper Feed
- Motor Assembly, Platen Open
- Motor Assembly, Ribbon Drive
- Operator Panel Assembly
- Paper Guide Assembly
- Paper Ironer
- Platen
- Platen Stop Assembly
- Resistors, Terminating
- controller board
- Ribbon Guide Assembly (L/R)
- RibbonMinder** Sensor
- Shaft, Splined
- Shaft, Support
- Shuttle Frame Assembly
- Spring, Extension, Hammer Bank
- Switch Assembly, Paper Detector
- Switch Assembly, Platen Interlock
- Tractor (L/R)
- Adjustment Procedures
- Belt, Paper Feed Timing, Adjustment (Figure 24)
- Belt, Platen Open, Adjustment (Figure 25)
- Paper Scale Alignment (Figure 26)
- Platen Gap Adjustment (Figure 27)
- Ribbon Guide Alignment (Figure 28)
- Adjusting The End Of Forms Distance
- Hammer Phasing Adjustment
- Coil Temperature Adjustment
- Dynamic Paper Tension Adjustment
- Tractor Belt Tension Adjustment
- Ethernet Initialization
- Parts Catalog
- Preventive Maintenance
- Cleaning The Printer
- Cleaning The Interior
- Cleaning The Shuttle Frame Assembly
- Cleaning The Card Cage Fan Assembly
- A Installing And Relocating The Printer
- B Communication Adapters
- Ethernet Troubleshooting Tips
- C Power Cords And Adapters
- D ASCII Codes
- E SureStak** Power Stacker
- Introduction
- How To Operate The Power Stacker
- Stacker Problems
- Removing The Power Stacker
- Installing The Power Stacker
- Replacing The Constant Force Spring
- Replacing The Timing Belts
- Replacing The Roller Drive Shaft
- Illustrated Parts Breakdown
- F Printer Specifications
- Ribbon Specifications
- warranty information
- Paper Specifications
- Labels
- Environmental Characteristics
- Electrical Characteristics
- Interfaces
- Printing Rates
- G Metric Conversion Tables
- Torque and Force
- Temperature
- H Torque Table
- I Abbreviations
|
451E SureStak ** Power StackerContentsIntroduction .................................................................................................................................................................. page 452How to Operate the Power Stacker.............................................................................................................................. page 453Stacker Operator Panel................................................................................................................................................ page 454Using The Power Stacker ............................................................................................................................................ page 455Loading and Starting the Power Stacker...................................................................................................................... page 457Stacker Problems......................................................................................................................................................... page 459Stacker First Inspection................................................................................................................................................ page 459Stacker Confidence Check........................................................................................................................................... page 460Stacker Motor Check.................................................................................................................................................... page 459Removing The Power Stacker ..................................................................................................................................... page 461Installing The Power Stacker ....................................................................................................................................... page 473Replacing The Constant Force Spring ......................................................................................................................... page 485Replacing The Timing Belts ......................................................................................................................................... page 487Replacing The Roller Drive Shaft.................................................................................................................................. page 491Illustrated Parts Breakdown ......................................................................................................................................... page 494List of Illustrations ........................................................................................................................................................ page 494
|
