JAI AM-800CL User Manual

Also see for AB-800CL: User manual

Contents

JAI AM-800CL User Manual Manual pdf 5 page image

AM-800CL / AB-800CL- 3 -- Contents -Before using AM-800CL and AB-800CL ....................................................- 6 -1. General ....................................................................................- 7 -2. Camera nomenclature .................................................................- 8 -3. Main features ............................................................................- 8 -4. Locations and functions ...............................................................- 9 -4.1 Locations and functions (C-mount) ...............................................................- 9 -4.2 Locations and functions (F-mount) ............................................................. - 10 -4.3 Rear panel .......................................................................................... - 11 -5. Input and output ......................................................................... - 12 -5.1 Connectors and pin assignment ................................................................. - 12 -5.1.1 Hirose 12Pin connector ...................................................................... - 12 -5.1.1.1 Figure ..................................................................................... - 12 -5.1.1.2 Pin assignment ........................................................................... - 12 -5.1.2 Camera Link connector ...................................................................... - 12 -5.1.2.1 Figure ..................................................................................... - 12 -5.1.2.2 Pin assignment ........................................................................... - 13 -5.1.3 DIP switch SW500 ............................................................................. - 13 -5.2 Camera Link interface ............................................................................ - 14 -5.3 Interface circuits .................................................................................. - 14 -5.3.1 Iris video output .............................................................................. - 14 -5.3.2 Trigger input................................................................................... - 15 -5.3.3 XEEN output ................................................................................... - 15 -5.4 Output ............................................................................................... - 16 -5.4.1 Digital output ................................................................................. - 16 -5.4.1.1 Bit allocation............................................................................. - 16 -5.4.1.2 Camera link output ..................................................................... - 16 -5.4.2 Partial scan readout (AOI) (Commands: STL, ETL) .................................... - 17 -5.4.2.1 Frame rate calculation if AOI is set ................................................. - 17 -5.4.2.2 If the bit allocation is set to 8,10 or 12bit and the binning is OFF or 2x1 ..... - 18 -5.4.2.3 If the bit allocation is set to 8,10 or 12bit and the binning is 1x2 or 2x2 ...... - 18 -5.4.2.4 If the bit allocation is set to RGB ..................................................... - 19 -5.4.2.5 Setting example 1 ....................................................................... - 19 -5.4.2.6 Setting example 2 ....................................................................... - 20 -5.4.2.7 Setting example 3 ....................................................................... - 20 -5.4.3 Binning (Command : BNC) (Only for AM-800CL) ......................................... - 21 -5.4.4 Bayer output pattern ........................................................................ - 21 -6. Sensor layout and timing ............................................................ - 22 -6.1 Sensor layout ....................................................................................... - 22 -6.2. Vertical timing (8bit, 10 bit or 12bit for Bit allocation) .................................... - 22 -6.2.1 If the binning control is BNC=0(OFF) or BNC=2(2x1) .................................... - 22 -6.2.1.1 AOI default setting ( Offset=0, Height=2472) ....................................... - 22 -6.2.1.2 AOI setting................................................................................ - 23 -6.2.2 If the binning control is BNC=1(1x2) or BNC=3(2x2) .................................... - 23 -6.2.2.1 AOI initial setting (Offset=0, Height=2472) ......................................... - 23 -6.2.2.2 AOI setting................................................................................ - 24 -6.3. Vertical timing (Bit allocation = RGB) ......................................................... - 25 -6.3.1 AOI initial setting ............................................................................. - 25 -6.3.2 AOI setting ..................................................................................... - 25 -6.4. Horizontal timing ................................................................................. - 26 -6.4.1 If the binning control is 0=OFF or 2=2x1 .................................................. - 26 -