JAI AM-800CL User Manual

Also see for AB-800CL: User manual

Contents

JAI AM-800CL User Manual Manual pdf 6 page image

AM-800CL / AB-800CL- 4 -6.4.2 If the binning control is 1=1x2 or 3=2x2 .................................................. - 26 -6.4.3 DVAL output if the Binning control is set to 2=2x1or 3=2x2 ........................... - 26 -6.4.4 LVAL-LOW level period ..................................................................... - 27 -7. Operating modes ...................................................................... - 28 -7.1. Acquisition control (Change the frame rate) ................................................ - 28 -7.2. Exposure setting .................................................................................. - 28 -7.2.1 Mode ........................................................................................... - 29 -7.2.2 Exposure time setting (Command: PE) ................................................... - 29 -7.2.3 Exposure sequence (Commands EXSQ,PES(N), PER(N), EXSR, EXSEP, PE1 ～PE16) - 29 -7.3. Trigger Control .................................................................................... - 29 -7.3.1 Selection of the trigger input(Command: TI) ............................................ - 29 -7.3.2 Trigger activation(Command: TA) ........................................................ - 29 -7.3.3 Trigger Overlap (Command: TO) ........................................................... - 30 -7.3.4 Trigger Dump (Command: TD) .............................................................. - 30 -7.4. Auto shutter control (Commands: ASC,ASCS,ASCEA,ASCEI)................................ - 30 -7.5. Normal continuous operation................................................................... - 31 -7.6. Timed mode (so-called EPS operation) ....................................................... - 32 -7.6.1 If the overlap setting is “OFF” ............................................................. - 32 -7.6.2 If the overlap setting is “Readout” ........................................................ - 33 -7.7. Trigger width mode (so-called PWC) .......................................................... - 34 -7.7.1 If the overlap setting is “Non Overlap” ................................................... - 34 -7.7.2 If the overlap setting is “Readout” ........................................................ - 35 -7.8. Edge-dump mode (so-called RCT) ............................................................. - 36 -7.9. PIV(Particle Image Velocimetry) ............................................................... - 37 -7.10. Operation and function matrix ............................................................... - 37 -8. Other functions ....................................................................... - 38 -8.1 Black level control (Command : BL) .......................................................... - 38 -8.2 Gain control (Relative commands GA,GJUT1,2,3) ........................................... - 38 -8.3 Tap control (Relative commands AWA,ABA,GJUT1, GJUT2,GJUT3)........................ - 38 -8.4. Exposure auto (Related Commands : ASC=1(ON),ASCS,ASCEA,ASCEI) .................... - 39 -8.5. Auto white balance (Related commands:AWB, PGS, PGR, PGGR, PGGB, PGB) ......... - 39 -8.6. Blemish compensation ........................................................................... - 40 -8.7. LUT (Relative commands LUTC,LUTR,LUYG, LUTB) ......................................... - 40 -8.8. Gamma (Command: GAMS) ..................................................................... - 41 -8.9. Flat Field Correction (FFC) (Command: SDR) ................................................ - 41 -8.10. Bayer color interpolation (Command : BCIC) (Only for AB-800CL) ...................... - 42 -8.11. Test pattern (Command: TPN) ................................................................ - 42 -8.12. Temperature sensor (Command : TMPO) .................................................... - 43 -9. Configuring the camera.............................................................. - 44 -9.1 RS-232C control .................................................................................... - 44 -9.2 Communication setting. .......................................................................... - 44 -9.3. Save and load functions ......................................................................... - 45 -9.4 Command list ...................................................................................... - 45 -10. Camera control tool ................................................................ - 53 -10.1. Control tool windows ........................................................................... - 53 -10.2. Camera Control Tool interface ................................................................ - 53 -10.2.1 About Window ............................................................................... - 53 -10.2.2 Communication Window ................................................................... - 54 -10.2.3 Camera Control Window ................................................................... - 56 -11. External appearance and dimensions .......................................... - 58 -12. Specifications ........................................................................ - 60 -12.1 Spectral response ................................................................................ - 60 -