12TK-860G/862GNote :You can clone the programmed data between the trans-ceiver listed below. Frequency version must be same.Slave TK-360G TK-360G TK-360G TK-360G TK-860G TK-860G TK-860GK M K4 M4 K M K3TK-370G TK-370G TK-370G TK-370G TK-862G TK-862GMaster K M K4 M4 K MTK-860G YES NO NO NO YES NO NOKTK-860G NO YES NO NO NO YES NOMTK-860G NO NO YES NO NO NO YESK3REALIGNMENTCloning cable(E30-3382-05)Fig. 2MBLPSBGNDPTT/TXDMEMICHOOK/RXDCMGNDREMOTE/TXDPTT/RXD8118Clone cableE30-3411-05 (TK-860G → TK-360G/370G)8. Self Programming Mode (TK-860G only)Write mode for frequency data and signalling etc. Mainlyused by the person maintaining the user equipment.8-1. Enter to the Self Programming ModeRemove D507 (Figure 3) from the TX-RX unit. Hold downthe [A] key and turn the power switch on. When enter theself programming mode, "SELF" is displayed. The modechanges autoically to Model Select Mode in about one sec-ond, and set up radio type, radio band & channel type andfrequency version.Notes :• To start the Firmware Programmer from KPG-56D, theFPRO path must be set up by the KPG-56D setup.• This mode cannot be entered if the Firmware program-ming mode is set to Disable in the Programming soft-ware (KPG-56D).• When programming the firmware, it is recommend tocopy the data from the floppy disk to your hard disk be-fore you update the radio firmware.Directly copying from the floppy disk to the radio may notwork because the access speed is too slow.6-4. Function1. If you press the [MON] switch while "PROG 576" is dis-played, the checksum is displayed. If you press the[MON] switch again (while the checksum is displayed),"PROG 576" is redisplayed.2. If you press the [A] switch while "PROG 576" is displayed,the display changes to "PROG 192" to indicate that thewrite speed is low speed (19200 bps). If you press the[A] switch again while "PROG 192" is displayed, the dis-play changes to "PROG 384", and the write speed be-comes the middle speed (38400 bps). If you press the[A] switch again while "PROG 384" is displayed, the dis-play returns to "PROG 576".Note :TK-862G indicate19200 bps : The LED flashes green and red alternately.38400 bps : The LED flashes orange.57600 bps : The LED lights orange.Normally, write in the high-speed mode.7. Clone ModeProgramming data can be transferred from one radio toanother by connecting them via their modular microphonejacks. The operation is as follows (the transmit radio is themaster and the receive radio is the slave).1. Turn the master TK-860G power ON with the [ ] keyheld down. The TK-860G displays "CLONE".2. Power on the slave TK-860G/862G.3. Connect the cloning cable (No. E30-3382-05) to themodular microphone jacks on the master and slave.4. Press the [SCN] key on the master while the master dis-plays "CLONE". The data of the master is sent to theslave. While the slave is receiving the data, "–PC–" is dis-played. When cloning of data is completed, the masterdisplays "END", and the slave automatically operates inthe User mode. The slave can then be operated by thesame program as the master.5. The other slave can be continuously cloned. When the[SCN] key on the master is pressed while the master dis-plays "END", the master displays "CLONE". Carry out theoperation in step 2 to 4.